Freeze Plugs/Tappet Covers

PDW Power

Supporting Vendor
Joined
Oct 17, 2007
Messages
426
Just releasing are new Freeze out plug set. It includes all 6 Freeze plugs for 12v motors. Soon to be released is 24v and CR editions.

The Rear freeze plug and front freeze plug are thinner than the four side plugs. The rear plug has a 1/2 NPT thread in it for any bypass you'd like to make or just a dead plug if no bypass is needed.

Complete Set of Six Plugs shipped to you for 199.00.
Also releasing Clear Tappet Cover shipped for 225.00.

If interested call us at 717-469-4378 or 717-557-7060 or send us a PM or Email.

Thank you, Shane at PDW
 

Attachments

  • IMG_20120726_124448-1.jpg
    IMG_20120726_124448-1.jpg
    26.3 KB · Views: 0
  • IMG_20120726_124503.jpg
    IMG_20120726_124503.jpg
    68.8 KB · Views: 0
  • IMG_20120726_130243.jpg
    IMG_20120726_130243.jpg
    26.1 KB · Views: 0
  • IMG_20120726_125408-1.jpg
    IMG_20120726_125408-1.jpg
    71.7 KB · Views: 0
  • IMG_20120726_125344.jpg
    IMG_20120726_125344.jpg
    46.9 KB · Views: 0
Also releasing this week of Heavy Duty pushrods for 12v's, 24/CR's and 6.0L Powerstrokes.


12v HD pushrods 269.00 Shipped.
24/CR HD pushrods 289.00 Shipped
6.0L Powerstrokes HD pushrods 239.00 Shipped.

If we get Orders of Ten of any set in next week I can take another 30 bucks off a set! Call shop or PM for more details or interest. Ill hold all orders till friday and place order if there's Ten orders of sets by then you'll get pushrods for 30 bucks cheaper!!!

If you bend or break one send it back and it will be replaced FREE!!
 
Thanks. Were almost finished with front clear cover that will also clear our adjustable gears also. Then working on 24v and CR front covers after 12v products are done.
 
The clear tappet cover would be perfect for my hoodless hotrod..

2 questions..
will it clear a p-pump?
what kind of seal does it use?
 
Will you sell.just the 4 side plugs? I.already Have the front And rear plugs

Sent from my SAMSUNG-SGH-I717 using Tapatalk 2
 
More info and pics on the side cover if you have them. How thick is it? Plexiglass or?
 
The clear covers are made from lexan and another material. They have like a blueish/tint look to them. We had them on 2 trucks and ran the hell out of them and no leaks or anything. you cant over tighten them either. We had spacers made for them so when tighten them down it doesnt break or crack it. They have a full o-ring around outside of cover. were working on adding LED's to the corners of couple different colors to light them up. Yes they clear P pumps no problems. around the 3rd bolt they are machined to clear P-pumps.

Were working on finishing up the clear front covers for 12v's also. Making them to clear adjustable timing gears also.

Yes i can sell just the side plugs for 149.00 shipped.
 
The side covers are 3/8 or 1/2 inch thick Ill double check tomorrow once get to shop
 
Heres picture of how we have it notched out to clear p-pumps. Also the cover is 3/8" thick.
 

Attachments

  • IMG_20120730_110852-1.jpg
    IMG_20120730_110852-1.jpg
    39.9 KB · Views: 0
Send you a PM in morning. Ill be talking to machine shop about front covers tomorrow.
 
Thanks!! Forgot to add the adj gear too. I think they would be awesome lit up and with how this engine is getting set up you should be able to see both.
 
Which adjustable gear? We didnt get any of covers lighted up with LED's yet. Wasn't sure if people would like them lite up. But if people like them ill talk with machine shop to make them and we can install LED's in them of bunch of different colors.
 
Will the front plug fit a CR block? If so, how far does it stick out and what is the cost?

Thanks
 
Were working on them right now at machine shop. If stick out from block its no more than 1/8" on 12v's ill double check tomorrow might only be a 1/16" inch from block. They fit behind the fan coupler on 12v's. Ill post findings in morning.
 
Back
Top