F250/Cummins Swap

That illusive #14 bolt....

Oil cooler on. Carter pump cover sandblasted and blacked out. Pretty ECM mount, not so pretty ECM.... And with another man's name on her no less. Knocked in the last 7 freeze plugs. Injectors cleaned and ready to install.



4a074ef85002d95fbc6ce75b8a8ca4ed.jpg
91f76d9b630b3f1532a309324b735d64.jpg
b0fd49317a24f5bfb2b1b3050826c284.jpg
947998c2a47778783c7950f0a43b6863.jpg
64db9a375b1981ecbf09951a8813286c.jpg
1563d927108919b7933297bdd0b1ef2c.jpg


Sent from my XT1575 using Tapatalk
 
Last edited:
It may or may not help anyone, but the CAT exhaust studs I'm using are 10903001 @~$4 each. I will get the spacer number when I figure out what engine they are from ?

OH yeah, mods can move this to the conversion forum. I guess I will use it as a build thread.

Sent from my XT1575 using Tapatalk
 
Wrong # on the studs. 224-5445

Trimmed to up-tube on the coolant bypass to make it fit more accurately. Mounted the water inlet.
bd7f353319f457c49a38cd0ff06bdecb.jpg
a06d0ecbe70ff6bff5e82553ce7a3458.jpg


Sent from my XT1575 using Tapatalk
 
What kind of setup are you going with? Mild towing type build or looking to make big Power?
 
600hp DD and maybe push it higher.

Short rod 6.4
Stock fly cut pistons
D&J valve springs
New valve seats
ARP head and main studs, flexplate and dampened bolts
Sleeved front seal
Carillo rods
188/200 hamilton
CM849
Reworked 6.7 harness
Fleece coolant bypass
Fleece 750 IP
Used 90hp injectors
SFI flex plate.
BD triple disc
DTT 47RE
Modified stock valve cover
Stock intercooler
Mishimoto rad.
Billet 63X68 from Zachezious Faylor
Stock 24V manifold with Cera cote, and the ports on the head are ceracoted
Manton pushrods

Bunch of hard parts from Mumau

Twins and injectors after I figure out where I want the power to be. Probably hang a 480 under the 63 with lots of gating.

Yeah, for the Ford (Trashpanda) Mitch.

Long to do list...


I still want to build a speed signal buffer for engine speed. I know guys are selling them, but I can't bring myself to pay them.

Sent from my XT1575 using Tapatalk
 
That's more serious than I thought, Awesome! Being stock rod and piston is the block decked? I've only played with 5.9 and haven't kept up with how it's done.
 
You've got it. Block is decked. Stock length rods.

Sent from my XT1575 using Tapatalk
 
So, I got ahead of myself. Installed the overhead without injectors. I stopped myself before I torqued and adjusted everything. #CATtechnicianproblems
90be30f8810f6d89107bc7cfcbb5248a.jpg
6edaca0c91802534df3e8be0ff37a4ef.jpg


Sent from my XT1575 using Tapatalk
 
In front of or behind the housing?
a995087e2a549b013ffb3ec1a228050c.jpg


Sent from my XT1575 using Tapatalk
 
Aaaahhh you and your hub porn.

I had no idea where the bracket went. I can look at an 06 tomorrow.

Sent from my XT1575 using Tapatalk
 
OK. So question of the day, and it's going to highlight the obvious.

I haven't degreed my cam. I'm going to have to.

Anyway, I'm checking piston to valve clearance with a dial indicator. (head is already installed)
I set TDC with a dial indicator through the injector bore.

Checking PTV with the dial indicator on intake #1, I have 0.115". 0.100" valve reliefs.

My question is, there is 0.015" piston to head clearance?

I know I should have checked all this before hand, but I was being a dick.

Sent from my XT1575 using Tapatalk
 
I shouldn't post **** like this early in the morning.....

Sent from my XT1575 using Tapatalk
 
Inching along.

Degreed cam, installed injectors, adjusted valves, cleaned plugs and installed, swapped fan bearing (no bolts to install on engine), installed oil pan (finally). Installed high pressure fuel system. Realized that there is no place on the 6.7 manifold plate for an intake manifold pressure sensor.
4e63a3f060950a4da1144ca4a296d6e3.jpg
e82be0bbd85e3957b270cfc6c7d7a2f4.jpg
2dbc4b9bca0f7c6d6bfbb00d216a97b2.jpg
22c1b565f80c23cd34341afca7ddf492.jpg
8e4dbc3aee8c289ad526ceed49ff2491.jpg
ee15af51a6280a90046637822a220076.jpg
f7b6f01dfce60e0b4ade017f5c675c2e.jpg
1feaa5dd8acaa8da21e1c7e81287bed1.jpg


Sent from my XT1575 using Tapatalk
 
What plugs are you running? NGK? Autolite?


Sent from my iPhone using Tapatalk Pro
 
Motorcraft. Unfortunately. ****ing 5.4 in an 8k truck. What were they thinking?

Sent from my XT1575 using Tapatalk
 
Back
Top