Highwayman
bored.
Do you have any consoles? I want a lid to try some upholstery on.
Refined list of 6.7 parts.
- Thread starter Mark Nixon
- Start date
Mark Nixon
No Savior among the flesh
What year do you need it for?
Mark.
Mark.
Highwayman
bored.
2010. seat style full size console, no cupholders.
Mark Nixon
No Savior among the flesh
I have that style in my '14 and I procured the cup holder style for it, because stickshifts limit cup holder usage. :hehe:
Mark.
Mark.
Empty_Pockets
Undercover Epa agent
Hey mark, do you happen to have a good alternator?
Mark Nixon
No Savior among the flesh
2008 6.7, complete runner with around 275,000 miles, comes with ECM, harnesses, turbo, 68rfe flywheel to fan hub, valve cover to pan, $3100 SHIPPED via Fastenal.
2008 6.7 longblock, that had a bad head gasket.
All cylinders looked great, still have cross hatch pattern, no scoring, or scuff marks, no marks or other obvious damage to the pistons, comes as a longblock, valve covers to oil pan, no fuel, exhaust, or air.
$2000 SHIPPED, via Fastenal.
I also have a few bare 6.7 blocks with rusty or damaged bores, $500 a block.
Reply, PM, Call or Text 402-780-5127
2008 6.7 longblock, that had a bad head gasket.
All cylinders looked great, still have cross hatch pattern, no scoring, or scuff marks, no marks or other obvious damage to the pistons, comes as a longblock, valve covers to oil pan, no fuel, exhaust, or air.
$2000 SHIPPED, via Fastenal.
I also have a few bare 6.7 blocks with rusty or damaged bores, $500 a block.
Reply, PM, Call or Text 402-780-5127
Mark Nixon
No Savior among the flesh
Above list is still current, plus the following:
All-standard 6.7 crank, should polish, $700 plus freight/BOL.
2007 6.7 cylinder head, minor pitting on the deck, needs cut and built, $325 plus freight/BOL.
Cannot ship Fastenal at this time.
Reply, PM, Call or Text 402-780-5127.
All-standard 6.7 crank, should polish, $700 plus freight/BOL.
2007 6.7 cylinder head, minor pitting on the deck, needs cut and built, $325 plus freight/BOL.
Cannot ship Fastenal at this time.
Reply, PM, Call or Text 402-780-5127.
Mark Nixon
No Savior among the flesh
Picked up the following core engines, all external AND internal parts are available.
2017 6.7, dropped a valve/seat, has turbo, injectors, CP3, crank, block, rail, lines, etc. $5-$2000
2008 6.7, bad head gasket, scored cylinder, has both valve covers, turbo, injectors, CP3, rail (no sensor) and lines, plus more. $5-$2000
Also have 2 lighter burns that spin over freely that can be parted.
Heavy stuff (150 pounds+) ships LTL on YOUR B.O.L. or I can rate it through freightcenter, or YOU pick up OR:
Buy enough to make it worth my while and I can deliver!
2017 6.7, dropped a valve/seat, has turbo, injectors, CP3, crank, block, rail, lines, etc. $5-$2000
2008 6.7, bad head gasket, scored cylinder, has both valve covers, turbo, injectors, CP3, rail (no sensor) and lines, plus more. $5-$2000
Also have 2 lighter burns that spin over freely that can be parted.
Heavy stuff (150 pounds+) ships LTL on YOUR B.O.L. or I can rate it through freightcenter, or YOU pick up OR:
Buy enough to make it worth my while and I can deliver!
Mark Nixon
No Savior among the flesh
Honestly, I have not gotten it disassembled, yet.
I am certain it did drop something into the piston because it spins over 360*, but has a slight bump, like there's pieces of valve, seat, or rings, just tapping the head and since the '13 up ones have a propensity for dropping seats, that's my best EDUCATED guess.
Might pull it down once it cools off around here tonight.
Mark.
I am certain it did drop something into the piston because it spins over 360*, but has a slight bump, like there's pieces of valve, seat, or rings, just tapping the head and since the '13 up ones have a propensity for dropping seats, that's my best EDUCATED guess.
Might pull it down once it cools off around here tonight.
Mark.
Mark Nixon
No Savior among the flesh
Not that high tech, here.
I'd almost guarantee the head is scrap.
Mark.
I'd almost guarantee the head is scrap.
Mark.
Mark Nixon
No Savior among the flesh
I have a few with decent CHRAs, but any actuators on them are nothing but cores.
$425 SHIPPED apiece.
Mark.
$425 SHIPPED apiece.
Mark.
Teamfreeman04
Livin' the Dream
Mark - you still have that go 08 long block?
Mark Nixon
No Savior among the flesh
Mark Nixon
No Savior among the flesh
Got the 2017 torn down and it appears to have broken a valve spring, then the piston ate the valve, on #4.
Engine didn't have but around 50k on it.
See attached pics.
I have the following parts from it:
CP3, $250 SHIPPED.
Fuel rail with lines & feed line, $200 SHIPPED.
5 injectors, $75 apiece SHIPPED.
Fuel filter/bowl, $100 SHIPPED.
Pump to bowl/filter lines, $30 SHIPPED.
Full set of pressed-tip rocker arms, with bases and bolts, $125 SHIPPED.
Rocker box, $55 SHIPPED.
LOWER valve cover, with bolts & grommets, $90 SHIPPED.
Bare block, needs bored/sleeved on #4, rest are still decent, $650 + freight.
All standard crank, may polish and go, $700 + freight.
Engine didn't have but around 50k on it.
See attached pics.
I have the following parts from it:
CP3, $250 SHIPPED.
Fuel rail with lines & feed line, $200 SHIPPED.
5 injectors, $75 apiece SHIPPED.
Fuel filter/bowl, $100 SHIPPED.
Pump to bowl/filter lines, $30 SHIPPED.
Full set of pressed-tip rocker arms, with bases and bolts, $125 SHIPPED.
Rocker box, $55 SHIPPED.
LOWER valve cover, with bolts & grommets, $90 SHIPPED.
Bare block, needs bored/sleeved on #4, rest are still decent, $650 + freight.
All standard crank, may polish and go, $700 + freight.
