Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
Shop Talk - Tool and Shop Discussion! Tool and Shop Discussion! |
11-20-2013, 03:27 PM
|
#1
|
Name: 99GreenCummins
Title: That guy....
Status: Not Here
Join Date: Feb 2011
Location: Marietta, Ohio
Member`s Gallery
Posts: 2,387
|
Let's talk shop heat
What's everyone using for shop heat?
We bought a new farm last winter and am now starting to design the inside of the current building to be my shop. Its a 3 bay 50x30 building. The shop part will be the lower level of the building. 1 wall is against a hill and the 2 sides are half covered from dirt.
In our old shop we used a old greenhouse heater. I want gas fed hanging type heater.
Will try to get a picture before dark since pictures are worth a thousand words.
__________________
Todd
Some farm trucks
2014 Ram 3500 19.5s, aisin
1999 Ram 2500,6 spd, typical mods
|
|
|
11-20-2013, 03:54 PM
|
#2
|
Name: StainlessRRA
Title: Advocatus diaboli
Status: Not Here
Join Date: Oct 2008
Location: Colorado
Member`s Gallery
Posts: 6,316
|
I run a gas fed hanging heater in one of my shops and it doesn't hold a candle to my radiant set up.
__________________
Kyle
Quote:
Originally Posted by wideopen
It would have helped if the picture didn't look like a Helen Keller Painting.
|
|
|
|
11-20-2013, 04:22 PM
|
#3
|
Name: 99GreenCummins
Title: That guy....
Status: Not Here
Join Date: Feb 2011
Location: Marietta, Ohio
Member`s Gallery
Posts: 2,387
|
Quote:
Originally Posted by StainlessRRA
I run a gas fed hanging heater in one of my shops and it doesn't hold a candle to my radiant set up.
|
As in hot water running through tubes in the floor?
__________________
Todd
Some farm trucks
2014 Ram 3500 19.5s, aisin
1999 Ram 2500,6 spd, typical mods
|
|
|
11-20-2013, 04:32 PM
|
#4
|
Name: SHughes
Title: Too much is never enough!
Status: Not Here
Join Date: Jan 2008
Location: Bellevue, NE
Member`s Gallery
Posts: 9,272
|
I use summer for heating and winter for cooling.
__________________
Quote:
Originally Posted by Joesixpack
That statement just reduced the collective IQ of the entire forum.
|
|
|
|
11-20-2013, 04:41 PM
|
#5
|
Name: TheSilverBullet
Title: All the correction factor
Status: Not Here
Join Date: Jan 2012
Location: Franklin,IA
Member`s Gallery
Posts: 1,598
|
Quote:
Originally Posted by SHughes
I use summer for heating and winter for cooling.
|
__________________
99 3500 black Laramie~Infinitive Performance Farrel Diesel Service Goerend Transmissions
98 12 valve with all the goodies from 2008
90 w250 "brownie" straight 6 standard transmission
Quote:
Originally Posted by dvst8r
Dying is always a way bigger concern than egt's...
|
|
|
|
11-20-2013, 05:09 PM
|
#6
|
Name: StainlessRRA
Title: Advocatus diaboli
Status: Not Here
Join Date: Oct 2008
Location: Colorado
Member`s Gallery
Posts: 6,316
|
Quote:
Originally Posted by 99GreenCummins
As in hot water running through tubes in the floor?
|
No, overhead and gas powered.
__________________
Kyle
Quote:
Originally Posted by wideopen
It would have helped if the picture didn't look like a Helen Keller Painting.
|
|
|
|
11-20-2013, 06:02 PM
|
#7
|
Name: Meyers Farms
Title: Too Much Time
Status: Not Here
Join Date: Dec 2007
Location: SW Ohio
Member`s Gallery
Posts: 2,508
|
We just went from gas fed forced air to gas fed overhead radiant heat. There is no comparison, the radiant heat is awesome. Radiant heat is just like the sun it heats objects not the air. With radiant heat a higher ceiling is preferred to let the heater cover a larger area. If no concrete is poured yet, radiant floor heat would be my vote. Radiant floor heat can be fed by a wood fired boiler if that is an option for you.
__________________
2013 Ford F-450 6.7 Auto, 4x4, Crew Cab
|
|
|
11-20-2013, 06:07 PM
|
#8
|
Name: Shawdrainage
Title: Shaw
Status: Not Here
Join Date: Feb 2010
Location: Wapakoneta, OH
Member`s Gallery
Posts: 1,617
|
Heated concrete floor. We did it in our 60x80x16. It's expensive, but it was worth it. We use about 1100 gal in propane for the year. And that's using the 40' bi fold door a decent amount
__________________
2016 Ram Powerwagon...... Stock for now
2006 Dodge Powerwagon "REHAB" Hot Street Puller. A whole truckload of SECERT SQUIRREL stuff, but still a small block HEMI!!!
1974 Dodge Powerwagon... Undecided roller.
|
|
|
11-20-2013, 07:26 PM
|
#9
|
Name: 99GreenCummins
Title: That guy....
Status: Not Here
Join Date: Feb 2011
Location: Marietta, Ohio
Member`s Gallery
Posts: 2,387
|
Concrete is already there, if I was pouring concrete it would get heated floors.
What's the cost compared to forced induction? I had never thought of it, our fairground buildings have them, they work well. Are there thermostats available for them?
__________________
Todd
Some farm trucks
2014 Ram 3500 19.5s, aisin
1999 Ram 2500,6 spd, typical mods
|
|
|
11-20-2013, 11:16 PM
|
#10
|
Name: Cummins2000
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2011
Location: Alberta
Member`s Gallery
Posts: 133
|
Also interested in this, my Dad's 40x40 insulated shop needs a permanent solution. Right now using a tiny 220V heater that keeps it about 10*C in -15* weather. Not good for electricity bill...
__________________
2000 Dodge 2500, ECLB NV4500
1990 VW Jetta 1.6 N/A Diesel, 5 speed
|
|
|
11-26-2013, 09:27 AM
|
#11
|
Name: 99GreenCummins
Title: That guy....
Status: Not Here
Join Date: Feb 2011
Location: Marietta, Ohio
Member`s Gallery
Posts: 2,387
|
Finally pictures
outside:
Inside: don't mind the mess, haven't got my work bench out here yet to organize it.
__________________
Todd
Some farm trucks
2014 Ram 3500 19.5s, aisin
1999 Ram 2500,6 spd, typical mods
|
|
|
11-26-2013, 09:32 AM
|
#12
|
Name: CumminNotRunnin
Title: Internet Mechanic
Status: Not Here
Join Date: May 2007
Location: North West, NJ
Member`s Gallery
Posts: 1,090
|
Subbed also interested in this.
__________________
Got Er Cummin
"A business that makes nothing but money, is a poor business."
-Henry Ford
|
|
|
11-26-2013, 09:42 AM
|
#13
|
Name: zstroken
Title: For $$$ your name here
Status: Not Here
Join Date: Sep 2006
Location: Western Michigan(by the lake)
Member`s Gallery
Posts: 23,151
|
Is there any insulation in the block wall?
__________________
2008 4x4 Megacab, 68RFE
97 Dodge gone....
24V P-Pump Mafia member #1(retired)
Thanks to Mumau Diesel, Goerend Transmission, Northeast Diesel Service!
|
|
|
11-26-2013, 10:04 AM
|
#14
|
Name: 99GreenCummins
Title: That guy....
Status: Not Here
Join Date: Feb 2011
Location: Marietta, Ohio
Member`s Gallery
Posts: 2,387
|
Quote:
Originally Posted by zstroken
Is there any insulation in the block wall?
|
Negative. Wish there was. 1956 is when it was constructed.
__________________
Todd
Some farm trucks
2014 Ram 3500 19.5s, aisin
1999 Ram 2500,6 spd, typical mods
|
|
|
11-26-2013, 10:07 AM
|
#15
|
Name: oldestof11
Title: Drag racer
Status: Not Here
Join Date: Jul 2007
Location: Dixon, IL
Member`s Gallery
Posts: 9,084
|
I x3643883 radiant heat. Our shop at work and the firehouse both have them on thermostats.
__________________
Jon
|
|
|
11-26-2013, 10:13 AM
|
#16
|
Name: nasty 2005
Title: Cummins Tech.
Status: Not Here
Join Date: Apr 2011
Location: S. Minnesota
Member`s Gallery
Posts: 301
|
I have radiant heat in both of my shops and love it,its definitely the way to go screw floor heat!
__________________
11' CCSB, MCC by Anarchy, AFE, Revmax, Flopro, Applied Performance Products, Caltracs, Leveled, 35's
Sold-95' ECLB
R.I.P-05' QCSB
|
|
|
11-26-2013, 10:14 AM
|
#17
|
Name: rawdog
Title: Too Much Time
Status: Not Here
Join Date: Jan 2007
Member`s Gallery
Posts: 2,196
|
Get yourself a 95% forced air furnace, put a plenum on it with dome taps and be done. Cheapest and easiest
__________________
|
|
|
11-26-2013, 10:54 AM
|
#18
|
Name: JoshH
Title: Too Much Time
Status: Not Here
Join Date: Apr 2007
Location: Tyler, Texas
Member`s Gallery
Posts: 648
|
I just bought a hanging gas heater yesterday. With a thermal output of 324,000 BTU/hr, I think it should heat up my 40x50 shop just fine.
__________________
2006 Silverado 2500HD
|
|
|
11-26-2013, 11:53 AM
|
#19
|
Name: zstroken
Title: For $$$ your name here
Status: Not Here
Join Date: Sep 2006
Location: Western Michigan(by the lake)
Member`s Gallery
Posts: 23,151
|
Folks mention the radiant heat, and personally 40-50 degrees is fine for me to work in. What I don't like being cold is the tools. I had always heard the radiant heat warms a person, and not the objects.
This year I am just running a 1500w electric heater, will see how it does compared to the pellet stove.
__________________
2008 4x4 Megacab, 68RFE
97 Dodge gone....
24V P-Pump Mafia member #1(retired)
Thanks to Mumau Diesel, Goerend Transmission, Northeast Diesel Service!
|
|
|
11-27-2013, 06:36 AM
|
#20
|
Name: Meyers Farms
Title: Too Much Time
Status: Not Here
Join Date: Dec 2007
Location: SW Ohio
Member`s Gallery
Posts: 2,508
|
Quote:
Originally Posted by zstroken
Folks mention the radiant heat, and personally 40-50 degrees is fine for me to work in. What I don't like being cold is the tools. I had always heard the radiant heat warms a person, and not the objects.
This year I am just running a 1500w electric heater, will see how it does compared to the pellet stove.
|
I agree with you about cold tools. Although, radiant heat heats the person and objects. If your tools are laying out they will be just as warm as you. Same idea as laying your tools in the sun. I personally love it.
The other benefit over forced air is recovery time when opening doors. If the doors never get opened its obviously not as big of a deal.
__________________
2013 Ford F-450 6.7 Auto, 4x4, Crew Cab
Last edited by Meyers Farms; 11-27-2013 at 06:39 AM.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 10:58 PM.
|