Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
07-20-2017, 01:16 PM
|
#1
|
Name: U.P Cummins
Title: Rookie
Status: Not Here
Join Date: Jun 2017
Location: Michigan
Member`s Gallery
Posts: 7
|
Computer 2001
I bought a 2001 block, computer was attached to the block but all wires were cut. plans are to pull the factory dash out of my 1999 and fab one and just run auto meter gauges. 24v will get a p7100. I think thats most of the import stuff?!
This being said I need computer help. Can I use the 01 computer or 99 computer? Do I need to send one out to be reprogramed? Would it be easier to just give to someone?
Does anyone have a wiring diagram or know where I can get a new harness?
Thanks!!!!
__________________
1999 S&B, 4in, FASS
|
|
|
07-20-2017, 02:21 PM
|
#2
|
Name: Mark Nixon
Title: No Savior among the flesh
Status: Not Here
Join Date: Feb 2009
Location: Brownville, Nebraska
Member`s Gallery
Posts: 8,676
|
You won't even need to run the ECM, if you're going P-pump and run aftermarket gauges.
The only thing you'd probably need is the PCM (firewall), if you're running an auto and speedometer.
Mark.
__________________
If you or I did business like the PEOPLE in government do business, we'd be put in jail. Government is coercive.
Anarchy: The state of existence where there are no masters & no slaves. Therefore, Anarchy means the ABSENCE OF SLAVERY, or, in other words, FREEDOM.
|
|
|
07-20-2017, 02:41 PM
|
#3
|
Name: U.P Cummins
Title: Rookie
Status: Not Here
Join Date: Jun 2017
Location: Michigan
Member`s Gallery
Posts: 7
|
ok, well the 2001 block i am going to use was pulled from a BUS? so not sure if that is going to be an issue... also i didn't pull the computer from the firewall, would i just be able to use the one in the truck (1999)? or do i need to go back and pull the one from the bus?
yes the truck will stay auto and i will be using an aftermarket speedo.
__________________
1999 S&B, 4in, FASS
|
|
|
07-20-2017, 03:56 PM
|
#4
|
Name: BigPapa
Title: Truckless
Status:
Here
Join Date: Jan 2008
Location: Springfield, TN
Member`s Gallery
Posts: 5,010
|
Quote:
Originally Posted by U.P Cummins
do i need to go back and pull the one from the bus?
|
I doubt there is one in the bus. If there is something in the bus, it will be worthless for your truck. Our buses have the Cummins ECM, an Allison tranny module, and a Bendix ABS module, that's it. No PCM.
__________________
Scott
2003 Avalanche Z71
Common sense is like deodorant. The people that need it most never use it.
|
|
|
07-20-2017, 04:11 PM
|
#5
|
Name: jasonc
Title: Too Much Time
Status: Not Here
Join Date: Nov 2009
Member`s Gallery
Posts: 4,396
|
This swap would be way easier and better to just get the anteater trans controller and not worry about the factory computers. Will control the trans better as a bonus.
|
|
|
07-20-2017, 04:49 PM
|
#6
|
Name: U.P Cummins
Title: Rookie
Status: Not Here
Join Date: Jun 2017
Location: Michigan
Member`s Gallery
Posts: 7
|
yes the 01 motor had an allison 545 attached to it but I'm going to use the 47re thats in the truck. ok so if i get an ant eater what do i need for electronics? fire punk controller for trans... no PCM.... no ECM? so where do i wire everything else?
sorry if i am missing something but I'm trying to learn lol.
__________________
1999 S&B, 4in, FASS
|
|
|
07-21-2017, 08:12 AM
|
#7
|
Name: jlbayes
Title: Too Much Time
Status: Not Here
Join Date: Mar 2011
Location: michigan
Member`s Gallery
Posts: 2,399
|
The ecm on the bus engine is not the same as the dodge controller. Will not work with what you want to do.
Anteater has a list of requirements on firepunks site iirc.
__________________
Jacob, 97 rclb
|
|
|
07-21-2017, 02:08 PM
|
#8
|
Name: U.P Cummins
Title: Rookie
Status: Not Here
Join Date: Jun 2017
Location: Michigan
Member`s Gallery
Posts: 7
|
ok so i won't need the pcm from anything but i will need the 99 ecm from the dodge to run the 01 motor and the rest of the truck, and i will need the FP controller for the trans. right?
__________________
1999 S&B, 4in, FASS
|
|
|
07-21-2017, 03:51 PM
|
#9
|
Name: jlbayes
Title: Too Much Time
Status: Not Here
Join Date: Mar 2011
Location: michigan
Member`s Gallery
Posts: 2,399
|
Pcm controls the dash. If you are gutting it there is no reason to use anything dodge other than what the anteater wants. Which would require a simple harness.
__________________
Jacob, 97 rclb
|
|
|
07-21-2017, 09:59 PM
|
#10
|
Name: U.P Cummins
Title: Rookie
Status: Not Here
Join Date: Jun 2017
Location: Michigan
Member`s Gallery
Posts: 7
|
nice ok thank you! ahah sorry this is so hard for me
__________________
1999 S&B, 4in, FASS
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 10:45 AM.
|