I got a package from Levi....

W

wdimig

New member
Blankets! they look awsome Levi!, guys pictures dont do justice, he is one hell of a blanket/sock maker! i got a manifold blanket, a turbo blanket, and 20' of wrap for the downpipe, i can't wait to get it all installed! ill have some pics up once i get the turbo. oh, and the manifold blanket, and turbo sock are painted silver with VHT Flame proof paint, should look awsome on the truck. thanks again Levi!

Wes
 
I did see 2 psi loss when I took off to have some rips repaired. :) and the A/C performance worked better this year with less heat under the hood.
 
JasonCzerak said:
I did see 2 psi loss when I took off to have some rips repaired. :) and the A/C performance worked better this year with less heat under the hood.
Click to expand...

Thanks for chiming in Jason. Rips are by far the biggest problem with the material used for the blankets. They take heat extremely well but they tend to want to rip if you're not gentle installing them and are difficult to remove without tearing them a little. The rips don't usually affect the blanket's performance or ability to hold on, it just makes them look like crap. I'm installing grommets into Jason's blankets to see if I can solve the ripping and tearing during install/removal. I'll post pics up later of the grommets installed so you guys can see.

As of right now, I've been fixing any of the blankets that have had problems for free (just shipping cost). I'm hoping the grommets should solve all of this and make the blankets that much better.

Levi
 
Turbo Performance said:
Thanks for chiming in Jason. Rips are by far the biggest problem with the material used for the blankets. They take heat extremely well but they tend to want to rip if you're not gentle installing them and are difficult to remove without tearing them a little. The rips don't usually affect the blanket's performance or ability to hold on, it just makes them look like crap. I'm installing grommets into Jason's blankets to see if I can solve the ripping and tearing during install/removal. I'll post pics up later of the grommets installed so you guys can see.

As of right now, I've been fixing any of the blankets that have had problems for free (just shipping cost). I'm hoping the grommets should solve all of this and make the blankets that much better.

Levi
Click to expand...



yep, and after 6 or so turbo removals with my htt turbo drama, these things were though hell and back and held up well for the most part.

Thanks again levi, I'll try to document the install with pics and what not.
 
JasonCzerak said:
yep, and after 6 or so turbo removals with my htt turbo drama, these things were though hell and back and held up well for the most part.

Thanks again levi, I'll try to document the install with pics and what not.
Click to expand...

I honestly never expected someone to install/remove 6 times in that short of a time span. I was pretty surprised myself that the blanket wasn't in worse condition.
 
Levi's customer service remains top notch in my book!!! Just may call him up about a setup for the new small turbo and stock manifold.
 
JasonCzerak said:
I stress test everything. ;-)
Click to expand...

You've made a believer out of me.


NickTF said:
Levi's customer service remains top notch in my book!!! Just may call him up about a setup for the new small turbo and stock manifold.
Click to expand...


Thanks Nick! To be honest I would rather make a good product, have good customer service, and do okay moneywise, than get rich selling junk and screwing people over. It seems like more and more people just want to get rich and don't care how many people get screwed in the process. In my book, that's not what it's about.
 
im running an armstrong performance manifold im just wondering if a blanket would still work with that manifold?
 
yoshi470 said:
im running an armstrong performance manifold im just wondering if a blanket would still work with that manifold?
Click to expand...

After looking at a few pics of the Armstrong manifold, I think the blanket would still work. As long as turbo mounting location is the same as stock the extra height in the manifold tubes above the turbo flange shouldn't be much of an issue.
 
got pictures finally!

well here's the pics of the manifold blanket, turbo blanket, and the new downpipe wraped. i must say the down pipe is alot harder to wrap than most people would think, it kept wanting to pull away from the pipe, and not lay flat, a couple extra clamps helped keep it against the pipe. will have some more pics once i get eveything mounted. enjoy!
 

Attachments

  • 053 [Desktop Resolution].JPG
    053 [Desktop Resolution].JPG
    114.2 KB · Views: 31
  • 054.JPG
    054.JPG
    109.7 KB · Views: 14
  • 055.JPG
    055.JPG
    110.9 KB · Views: 24
  • 056.JPG
    056.JPG
    108.6 KB · Views: 19
  • 057.JPG
    057.JPG
    113.9 KB · Views: 22
  • 058.JPG
    058.JPG
    113.7 KB · Views: 19
and the downpipe pics
 

Attachments

  • 046.JPG
    046.JPG
    114.9 KB · Views: 46
  • 048.JPG
    048.JPG
    115.7 KB · Views: 30
  • 049.JPG
    049.JPG
    112.9 KB · Views: 29
  • 050.JPG
    050.JPG
    106.1 KB · Views: 32
levi does good work. you will like those for sure.:Cheer: i just hate having to listen to that damn sewing machine upstairs at the shop
 
Looks good Wes, you did a good job wrapping the downpipe. I've seen some real disasters. I'm glad you like the blankets, I'm sure you'll like the way they perform even better. Thanks again. :Cheer:
 
You must log in or register to reply here.
Back
Top