Towing compounds on a near stock 95
- Thread starter turbo2387
- Start date
12vchevydually
my mind is churnin!
I heard the guy that owns that thing is a real douche rocket!
I also heard that he thinks most of the people left in the diesel world suck!
Signature600
THA MAN!
Financial Mistake
New member
Weston builds a 78, I wanna say his has a 119 exducer as well, not sure if EDs was a 110 or not
Sent from my iPhone using Tapatalk
Signature600
THA MAN!
It was a 6 blade FMW wheel, but I don't remember the exducer measurement.
It sings, I remember that...and spools like a 475.
Chris
Financial Mistake
New member
@signature600
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Financial Mistake
New member
And I'm sure Weston would be more than happy to change turbines upon request.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
JQmile
Comp Diesel Sponsor
I like tiny twins too....my 95 made 430rwhp with a 57 and 71 combo, and made 393rwhp (sustained) on a load dyno at 1100 egt. As in, we could just sit there at that power level and rpm until either the dyno or truck's radiator overheated.
Added more fuel and the truck eventually made 601rwhp just spinning the 71 harder. Fun setup.
Added more fuel and the truck eventually made 601rwhp just spinning the 71 harder. Fun setup.
Bodacious
Comp Diesel Sponsor
Nice. I love the hot pipe!!
Ram12vcummins
New member
What intake is that?
Sent from my iPad using Tapatalk Pro
Sent from my iPad using Tapatalk Pro
Bodacious
Comp Diesel Sponsor
Here's how we did a set on a 1st gen...S300G over an S478 (billet 6 blade wheel, 83mm turbine in a 1.10 T6 housing)...spools STUPID fast for the amount of air it moves.
1st gens are EASY to package twins into...
Chris
I like that as well. Looks to be an aftercooler?? moded??
Signature600
THA MAN!
Yes, Josh would have to fill you in on exactly what's done, but I remember s300g, over s478, ve maxed out with a set of 6x.016's, water after cooler running an ice water tank out back, we might have injected water meth to it too, been a while. 1984 D100 with a bone stock 727 and a 9" rear spinning 2.90 gears.
Chris
Chris
12vchevydually
my mind is churnin!
Its stupid simple. It does have a Snow W/M kit on it. Bone stock 727 with a 275 gear 9in with Moser 31 spline. 3200 gov spring. Hillbilly spring on waste gate on the small charger.
I have to say Chris(sig600) was the master mind on the chargers, I told him what it had to do to work with the VE pump and he knocked it out of the park!!
I have to say Chris(sig600) was the master mind on the chargers, I told him what it had to do to work with the VE pump and he knocked it out of the park!!
Bodacious
Comp Diesel Sponsor
I had pondered on trying a set of 2.73's out of a Lincloln 9" ford. I ran them behind my 460 in the day. At least I could get better use out of the three 727's and two A-518's.
Just need to figure out how to gear the front up there with it.
Signature600
THA MAN!
On a light truck and the VE pump it absolutely loves the tall gears. The VE is RPM limited as hell, but they want to build torque and fuel down low...I was amazed how the tall gears work.
Chris
turbo2387
Nipple Fluffer
Sold the dodge with a stock turbo and installed the compounds on my buddies 2010 fummins. 14,000 miles later and he is still in love. Had to re work a few things to make them fit. Some AC stuff is extremely close to some hot stuff but its all in and going. His truck is bone stock other than .024 delivery valves and 4k springs. Absolutly smokeless pulling the 5th wheel loaded through the hills.
