Pump support bracket and throttle return spring

PPUMPFUMMINS

PPUMPFUMMINS

New member
Guys need some help, finishing my p24v engine, bought a pump with bolts and brackets in a box. My pump has a single return spring and two brackets with it. If anyone has pics of their throttle return and pump support bracket, I would appreciate if they posted so I can figure this thing out. Pump was out of a 97 auto truck.
 
attachment.php



Thats the linkage setup on my p-pump 24v, out of the Schieds kit. The older 12v stuff was basically the same, slightly different.

I don't have a picture uploaded of the support bracket, but its a heavy tee, about 1" wide, 3-4" long and 2" high IIRC, two threaded holes to where it mounts on the pump, and a threaded hole on the bottom part of the tee where it will bolt to the mount on the block. The block mount has the side profile of a hockey stick, more or less.

The older style has just a bent bracket off the pump, similar to a piece of angle iron, that has a bolt hole axially along the pump to mount to the block mount. I forget what the block mount looks like though.
 
Tate said:
attachment.php



Thats the linkage setup on my p-pump 24v, out of the Schieds kit. The older 12v stuff was basically the same, slightly different.

I don't have a picture uploaded of the support bracket, but its a heavy tee, about 1" wide, 3-4" long and 2" high IIRC, two threaded holes to where it mounts on the pump, and a threaded hole on the bottom part of the tee where it will bolt to the mount on the block. The block mount has the side profile of a hockey stick, more or less.

The older style has just a bent bracket off the pump, similar to a piece of angle iron, that has a bolt hole axially along the pump to mount to the block mount. I forget what the block mount looks like though.
Click to expand...
Thanks bud, after some research and looking at your post, found out my pump went to scheid with bracket on and came back without it........ Have a call into them, but I may have to buy a new one.
 
If this truck is in a 98-02 truck granby truck shop makes a really nice bracket that makes it really clean setup, that is if youre not running an apps


Sent from my iPhone using Tapatalk
 
I actually have my pump from my 94 sitting on the bench, i should be able to get a good picture in the morning


Sent from my iPhone using Tapatalk
 
16b25f60e285217a8c8b1897a89e255a.jpg

dec872951b4062a29026b46fee69f01e.jpg

1-throttle cable
2-tv cable
3-cruise control
I think thats right
Are you looking for how the apps mounts onto the throttle linkage?


Sent from my iPhone using Tapatalk
 
I have a bracket that bolts somewhere? It a piece of angle with a knob to retain a spring, and one double wound spring. Issue is I currently have no return setup. I think the double wound spring and this bracket is for the return but don’t know where it mounts. And my pump doesn’t have the setup with the double springs in the back, like the later p pumps. My set up looks like the one u have pictured above.
 
I think this is what youre looking for?
It has a long bolt that goes down into the support for the pump
1b8f078fa1643bf6a949c8a0597ecbf3.jpg

202f0bac4c8b3706e718b9f386ed3f89.jpg

be74673f2869936bed2f90a9376e6010.jpg



Sent from my iPhone using Tapatalk
 
I cannot find the bracket that i have online, it looks like it says 302319
Is this not the bracket you are searching for?
dccea884080632b91e017f64fd310f38.jpg

ca76e40c5f8b6d61f2de9200002ce137.jpg

Take some pictures of what you have


Sent from my iPhone using Tapatalk
 
[ame]http://i1032.photobucket.com/albums/a405/alwaysdiesel/94-96spring_zpsbds4bupt.jpg[/ame]
This is the bracket I have
 
Id modify that one and create something similar to what i have if i were you. I can take some pics with measurements to make it easier if you want?


Sent from my iPhone using Tapatalk
 
You must log in or register to reply here.
Back
Top