Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Tech Area- Dodge > Dodge Tech > 2007.5-2013 6.7L
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Closed Thread
 
Thread Tools
Old 05-16-2018, 06:31 PM   #1
xDiesel03
 
xDiesel03's Avatar

Name: xDiesel03
Title: Diesel Enthusiast
Status: Not Here
Join Date: Oct 2013
Member`s Gallery
Posts: 225
Rail Pressure Stuck at 120MPa / 17.4k psi

I’m looking for some advice on how to troubleshoot this issue. I was driving from TN to MI and towards the end of the trip all of a sudden my truck developed a bad surge and erratic rail pressure. After a few minutes the rail pressure stuck at 120MPa / 17.4k psi. It’s the same pressure no matter what RPM or throttle position. What I’ve tried so far is reflashing the ECM, replacing the rail pressure sensor, and replaced the rail pressure sensor pigtail. None of this made a difference.

Truck has an ATS dual CP3 controller and I have a Cummins FCA in the top pump.

Unplugging the FRP sensor connection does nothing to commanded or actual value. Unplugging either FCA also does nothing to commanded or actual value, but you can hear the engine/injector rattle so it’s definitely increasing rail pressure. All I can think now is to check continuity for each FRP sensor wire to the ECM, and if that’s good I would think it has to be a bad ECM. Anyone have the pin out for a 2012 6.7 and/or recommendations?
__________________
2003 2500 QCSB 4x4 3.73 - Firepunk HPT Tuned, BBI Stage 2's, DAP 63/68/12, Hamilton [624/1050 and 680/1206 with Water/Meth]

2012 2500 CCSB 4x4 3.73 Firepunk EFI and Comp3, D&J Built 6.7L, S&S 200%, ATS Dual CP3 w/ Exergy 12mm, S366/S483 Compounds [1086/2289]
 
Old 05-17-2018, 07:54 PM   #2
TBittner
 
TBittner's Avatar

Name: TBittner
Title: Too Much Time
Status: Not Here
Join Date: Mar 2010
Location: Irwin, PA
Member`s Gallery
Posts: 462
Ats controller?
 
Old 05-17-2018, 08:51 PM   #3
okie18
 
okie18's Avatar

Name: okie18
Title: Too Much Time
Status: Not Here
Join Date: Jan 2009
Location: Leon, OK
Member`s Gallery
Posts: 996
Pull the belt off the second pump and plug the stock fca connection to the stock location cp3. That'll narrow it down to the 2nd pump/fca or the controller if it runs good. If not look at the stock location pump/fca or plug.

Sent from my SAMSUNG-SM-G890A using Tapatalk
__________________
2014 2500 Longhorn HPP tuned
04 2500 RCLB 4x4
Smarty UDC, AD 150, Fletcher Cam & Springs, Steed Speed, Thuren, Exergy 60%, Firepunk Comp 3, Anarchy Dual Cp3's, 467 fmw, 861/1427 930 on spray
 
Old 05-17-2018, 09:46 PM   #4
xDiesel03
 
xDiesel03's Avatar

Name: xDiesel03
Title: Diesel Enthusiast
Status: Not Here
Join Date: Oct 2013
Member`s Gallery
Posts: 225
Ok- looks like I got it. Two nights ago I switched the rail pressure sensor and it didn’t fix the issue. I tested the pigtail connection and didn’t have voltage to the signal wire with key on engine off so I picked up a new pigtail. Last night, thinking it was just the pigtail and not the sensor, I put the old sensor back in after I replaced the pigtail and didn’t run it with new sensor. Tonight I swapped in the new sensor and it idles at 7.5k psi like it’s suppsed to. The truck was giving some weird WOT surging issues in the weeks leading up to this so I think the wire was starting to come loose, and when I was wiggling things around trying to see if I had a loose connection it probably lost its connection. Two separate issues, and very annoying.
__________________
2003 2500 QCSB 4x4 3.73 - Firepunk HPT Tuned, BBI Stage 2's, DAP 63/68/12, Hamilton [624/1050 and 680/1206 with Water/Meth]

2012 2500 CCSB 4x4 3.73 Firepunk EFI and Comp3, D&J Built 6.7L, S&S 200%, ATS Dual CP3 w/ Exergy 12mm, S366/S483 Compounds [1086/2289]
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:36 AM.

 


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2024, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com