Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
Sponsor Forums Read up on new products/promotions, or ask a Sponsor in their own forum. |
08-14-2018, 05:27 AM
|
#1
|
Name: RockinRam96
Title: Too Much Time
Status: Not Here
Join Date: Sep 2011
Location: Shortsville, NY
Member`s Gallery
Posts: 2,700
|
GT55 Exhaust Housing
Looking for a Garett GT55 divided exhaust housing. I currently have a 1.00 a/r undivinded exhaust housing. Looking for something like a 1.12 a/r or a 1.24 a/r.
Running it on a mechanical caterpillar 3406, with a factory pump maxed out, 100% over nozzles and the air fuel ratio controller eliminated, turning 2700 rpm at high idle.
Sent from my iPhone using Tapatalk
__________________
05 Jeep Liberty CRD
11 Dodge
1986 Freightliner Cat 425
|
|
|
08-14-2018, 07:52 PM
|
#2
|
Name: DieselheaD
Title: Too Much Time
Status: Not Here
Join Date: Jun 2007
Location: CA
Member`s Gallery
Posts: 2,731
|
Contact chase Fleece.
|
|
|
08-15-2018, 11:24 AM
|
#3
|
Name: TTR 21
Title: Human Spear
Status: Not Here
Join Date: Sep 2009
Location: West Jordan, UT
Member`s Gallery
Posts: 1,158
|
We have 1.37 a/r divided housings on the shelf ready to ship
__________________
Budget Beater: 9.36 @ 148 MPH
|
|
|
08-15-2018, 02:15 PM
|
#4
|
Name: DieselheaD
Title: Too Much Time
Status: Not Here
Join Date: Jun 2007
Location: CA
Member`s Gallery
Posts: 2,731
|
Quote:
Originally Posted by TTR 21
We have 1.37 a/r divided housings on the shelf ready to ship
|
Is that a 408804-0034 Garrett tv81 turbine Housing that gets machined or is it ready to fit the 111/102 gt55 turbine off the shelf ?
|
|
|
08-15-2018, 02:42 PM
|
#5
|
Name: Leiffi
Title: Too Much Time
Status: Not Here
Join Date: Jan 2013
Member`s Gallery
Posts: 1,381
|
Quote:
Originally Posted by DieselheaD
Is that a 408804-0034 Garrett tv81 turbine Housing that gets machined or is it ready to fit the 111/102 gt55 turbine off the shelf ?
|
https://hardwayperformance.com/mfgr/...6-divided.html
|
|
|
08-15-2018, 05:21 PM
|
#6
|
Name: TTR 21
Title: Human Spear
Status: Not Here
Join Date: Sep 2009
Location: West Jordan, UT
Member`s Gallery
Posts: 1,158
|
Quote:
Originally Posted by DieselheaD
Is that a 408804-0034 Garrett tv81 turbine Housing that gets machined or is it ready to fit the 111/102 gt55 turbine off the shelf ?
|
Not sure on the actual part number but I do know we machine them to fit the GT55 turbine wheel. We have our own made up part number we use for them to include the machining and everything. I have around 50 of them I think
__________________
Budget Beater: 9.36 @ 148 MPH
|
|
|
08-15-2018, 05:42 PM
|
#7
|
Name: DieselheaD
Title: Too Much Time
Status: Not Here
Join Date: Jun 2007
Location: CA
Member`s Gallery
Posts: 2,731
|
Quote:
Originally Posted by Leiffi
|
I already have one. Was just trying to source one for a friend to avoid paying retail. Found it but it does need machined.
Thanks for the insight kipp
|
|
|
08-15-2018, 08:23 PM
|
#8
|
Name: RockinRam96
Title: Too Much Time
Status: Not Here
Join Date: Sep 2011
Location: Shortsville, NY
Member`s Gallery
Posts: 2,700
|
Quote:
Originally Posted by TTR 21
Not sure on the actual part number but I do know we machine them to fit the GT55 turbine wheel. We have our own made up part number we use for them to include the machining and everything. I have around 50 of them I think
|
What’s the II part number? What’s the price?
Sent from my iPhone using Tapatalk
__________________
05 Jeep Liberty CRD
11 Dodge
1986 Freightliner Cat 425
|
|
|
08-15-2018, 10:05 PM
|
#9
|
Name: SmokinCAT
Title: Cheap and Easy.
Status: Not Here
Join Date: Sep 2008
Location: Hillsboro, Oh
Member`s Gallery
Posts: 3,162
|
Quote:
Originally Posted by TTR 21
Not sure on the actual part number but I do know we machine them to fit the GT55 turbine wheel. We have our own made up part number we use for them to include the machining and everything. I have around 50 of them I think
|
What’s the purpose of going this route versus the stock caterpillar application 1.37 divided?
|
|
|
08-15-2018, 11:10 PM
|
#10
|
Name: DieselheaD
Title: Too Much Time
Status: Not Here
Join Date: Jun 2007
Location: CA
Member`s Gallery
Posts: 2,731
|
Quote:
Originally Posted by SmokinCAT
What’s the purpose of going this route versus the stock caterpillar application 1.37 divided?
|
The 408804-0034 is the 1.37 A/R Garrett TV series turbine housing (110mm/97mm) , CAT P/N (9N2032), GT55 turbine is (112/102) which means it needs work to fit.
Last edited by DieselheaD; 08-15-2018 at 11:15 PM.
|
|
|
08-16-2018, 08:01 AM
|
#11
|
Name: SmokinCAT
Title: Cheap and Easy.
Status: Not Here
Join Date: Sep 2008
Location: Hillsboro, Oh
Member`s Gallery
Posts: 3,162
|
Quote:
Originally Posted by DieselheaD
The 408804-0034 is the 1.37 A/R Garrett TV series turbine housing (110mm/97mm) , CAT P/N (9N2032), GT55 turbine is (112/102) which means it needs work to fit.
|
Perhaps you misunderstood, there is a GT55 1.37 that cat uses.
|
|
|
08-16-2018, 08:30 AM
|
#12
|
Name: DieselheaD
Title: Too Much Time
Status: Not Here
Join Date: Jun 2007
Location: CA
Member`s Gallery
Posts: 2,731
|
Quote:
Originally Posted by SmokinCAT
Perhaps you misunderstood, there is a GT55 1.37 that cat uses.
|
It’s clear now! is there only 1 a/r available or is there other options?
|
|
|
08-16-2018, 08:39 AM
|
#13
|
Name: SmokinCAT
Title: Cheap and Easy.
Status: Not Here
Join Date: Sep 2008
Location: Hillsboro, Oh
Member`s Gallery
Posts: 3,162
|
Quote:
Originally Posted by DieselheaD
It’s clear now! is there only 1 a/r available or is there other options?
|
I believe there is also a 1.58, but nothing smaller.
For that you would have to look at Cummins and Detroit apps, there is a 1.18 divided with internal gate that they use.
|
|
|
08-16-2018, 10:52 AM
|
#14
|
Name: RockinRam96
Title: Too Much Time
Status: Not Here
Join Date: Sep 2011
Location: Shortsville, NY
Member`s Gallery
Posts: 2,700
|
Quote:
Originally Posted by SmokinCAT
I believe there is also a 1.58, but nothing smaller.
For that you would have to look at Cummins and Detroit apps, there is a 1.18 divided with internal gate that they use.
|
Will they all fit the GT55 frame and wheel or do they all need machining to fit correctly?
Which option do you suggest? How do you think the 1.37 a/r will hold up on my set up?
__________________
05 Jeep Liberty CRD
11 Dodge
1986 Freightliner Cat 425
|
|
|
08-16-2018, 11:42 AM
|
#15
|
Name: DieselheaD
Title: Too Much Time
Status: Not Here
Join Date: Jun 2007
Location: CA
Member`s Gallery
Posts: 2,731
|
Quote:
Originally Posted by SmokinCAT
I believe there is also a 1.58, but nothing smaller.
For that you would have to look at Cummins and Detroit apps, there is a 1.18 divided with internal gate that they use.
|
What’s the p/n for 1.37 divided gt55?
|
|
|
08-16-2018, 11:44 AM
|
#16
|
Name: SmokinCAT
Title: Cheap and Easy.
Status: Not Here
Join Date: Sep 2008
Location: Hillsboro, Oh
Member`s Gallery
Posts: 3,162
|
Quote:
Originally Posted by DieselheaD
What’s the p/n for 1.37 divided gt55?
|
The cat part number is 183-6629, I have no idea what that would cross to in a garrett part number.
|
|
|
08-16-2018, 11:45 AM
|
#17
|
Name: SmokinCAT
Title: Cheap and Easy.
Status: Not Here
Join Date: Sep 2008
Location: Hillsboro, Oh
Member`s Gallery
Posts: 3,162
|
Quote:
Originally Posted by RockinRam96
Will they all fit the GT55 frame and wheel or do they all need machining to fit correctly?
Which option do you suggest? How do you think the 1.37 a/r will hold up on my set up?
|
I am a fan of the 1.18, it was very comparable to a 1.65 S400.
|
|
|
08-17-2018, 07:56 AM
|
#18
|
Name: RockinRam96
Title: Too Much Time
Status: Not Here
Join Date: Sep 2011
Location: Shortsville, NY
Member`s Gallery
Posts: 2,700
|
Quote:
Originally Posted by SmokinCAT
I am a fan of the 1.18, it was very comparable to a 1.65 S400.
|
Will this fit the factory Garrett GT55 or will it need machining as mentioned above?
__________________
05 Jeep Liberty CRD
11 Dodge
1986 Freightliner Cat 425
|
|
|
08-28-2018, 08:21 AM
|
#19
|
Name: i-r-truckdriver
Title: Think less. Stupid more
Status: Not Here
Join Date: Jul 2018
Location: Wi
Member`s Gallery
Posts: 181
|
Any housing other than the 1.18 that is internal gated?
|
|
|
08-29-2018, 08:01 AM
|
#20
|
Name: SmokinCAT
Title: Cheap and Easy.
Status: Not Here
Join Date: Sep 2008
Location: Hillsboro, Oh
Member`s Gallery
Posts: 3,162
|
Quote:
Originally Posted by RockinRam96
Will this fit the factory Garrett GT55 or will it need machining as mentioned above?
|
Yes, it is an actual GT55 housing.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 09:35 PM.
|