Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Tech Area- Dodge > Dodge Competition and Performance > P-Pump 24Valve
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Closed Thread
 
Thread Tools
Old 07-15-2018, 03:52 PM   #1
Rollin Coal02
 
Rollin Coal02's Avatar

Name: Rollin Coal02
Title: Diesel Enthusiast
Status: Not Here
Join Date: Dec 2008
Location: Green Bay, WI
Member`s Gallery
Posts: 207
ECM Relocate with Billet Tappet Cover?

Anyone running a Billet Tappet cover with breathers with a P pumped 24V? Using the stock tappet cover i just pushed the ECM to the back of the engine and that worked fine. Now the breathers will be in the way. Anyone found a good way to mount the ECM with this setup? PFA
Click the image to open in full size.
__________________
02 QCSB 6 Speed|215 P-Pump 600cc 28*|Balanced Rotating Assy|Billet Rods|64/S480|Steed Speed|SAC 7x12|131 DVs|AirDog200|Hamilton 194/220|Oversized Intake Valves|Port Polished Intake/Exhaust|Valair Tripple Disk|.084 Lines/Tubes|Side Draft Intake|4.88|

Last edited by Rollin Coal02; 07-15-2018 at 03:56 PM.
 
Old 07-15-2018, 10:00 PM   #2
bigstacks95
 
bigstacks95's Avatar

Name: bigstacks95
Title: Diesel Doc
Status: Not Here
Join Date: Jul 2008
Location: Falls Village, CT
Member`s Gallery
Posts: 2,030
I have built a bracket to hang the ECM off the master cylinder to booster mounting bolt before.
__________________
--Dave--

58 Dodge Power Wagon 3.0 Limited Pro Stock diesel pulling truck

2020 Ram 3500 HO/Aisin Laramie/night tow rig
 
Old 07-19-2018, 08:32 PM   #3
rucummins
 
rucummins's Avatar

Name: rucummins
Title: Too Much Time
Status: Not Here
Join Date: Jan 2010
Location: Richmond, VA/ Buffalo NY
Member`s Gallery
Posts: 957
I took a piece of angle iron and bolted the ecm on that and then used the 2 bolt holes above the motor mount to secure it to the block
__________________
01 ppump, almost driveable again...
 
Old 07-20-2018, 01:42 PM   #4
Yotadzl

Name: Yotadzl
Title: Diesel Enthusiast
Status: Not Here
Join Date: Feb 2016
Location: Oregon
Member`s Gallery
Posts: 234
I've used longer bolts or threaded rod and spacers to mount the ecm over the vent box. Obviously with your set up it would need 90 degree fittings for the vents, but its doable. It would hang kinda far out there with that breather setup.
__________________

'85 Yota Crawler-2l diesel, custom built VE (by me), custom T25 turbo. Slow but fun!
'95 Cummins grampa truck, embarrassingly stock
'12 Cummins, deleted
 
Old 07-20-2018, 02:19 PM   #5
Justappumped24v
 
Justappumped24v's Avatar

Name: Justappumped24v
Title: Too Much Time
Status: Not Here
Join Date: Feb 2016
Location: Illinois
Member`s Gallery
Posts: 1,311
I welded angle to the frame and flipped it around plenty of slack on the harness and got it out of the way
Click the image to open in full size.Click the image to open in full size.Click the image to open in full size.


Sent from my iPhone using Tapatalk Pro
__________________
05 QCSB24v HTD 6.8L, DDP fueling PDD shifted
2011 MCSB 6.7, built 68rfe
 
Old 08-04-2018, 09:29 PM   #6
Rollin Coal02
 
Rollin Coal02's Avatar

Name: Rollin Coal02
Title: Diesel Enthusiast
Status: Not Here
Join Date: Dec 2008
Location: Green Bay, WI
Member`s Gallery
Posts: 207
Thanks for the ideas guys!
__________________
02 QCSB 6 Speed|215 P-Pump 600cc 28*|Balanced Rotating Assy|Billet Rods|64/S480|Steed Speed|SAC 7x12|131 DVs|AirDog200|Hamilton 194/220|Oversized Intake Valves|Port Polished Intake/Exhaust|Valair Tripple Disk|.084 Lines/Tubes|Side Draft Intake|4.88|
 
Old 08-05-2018, 07:57 AM   #7
BlackasCoal
 
BlackasCoal's Avatar

Name: BlackasCoal
Title: Too Much Time
Status: Not Here
Join Date: Sep 2011
Location: Camp Lejeune NC but grown in PA
Member`s Gallery
Posts: 628
Not mine and on a CR but
Click the image to open in full size.
__________________
07.5 MCSB, Thuren/Carli/King, 35" Toyos MT's, 17" Methods, Miller’s Machine Shop 6.4 w/ Wagler long rods, QSB pistons, 188/220 cam, Ported/big valve head, Muldoons Phat shaft 48re w/ anteater, DDP 5.9 fuel, Firepunk 66/85, Firepunk EFI
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:59 AM.

 


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2024, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com