Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Tech Area- Dodge > Dodge Competition and Performance
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Dodge Competition and Performance General Dodge Competition and Performance Discussion

Reply
 
Thread Tools
Old 08-01-2018, 08:33 AM   #1
iride813
 
iride813's Avatar

Name: iride813
Title: Green Behind the Ears
Status: Not Here
Join Date: Mar 2018
Location: Tennessee
Member`s Gallery
Posts: 36
Machining delivery valves

Sorry for all the post past few days, but anyways. I have a set of 191 delivery valves Iíve decided to go ahead and turn them into full cuts. That being said I was wondering what I should turn the diameter down to once shoulder is gone and how accurate they need to be within each other. Thanks!
  Reply With Quote
Old 08-01-2018, 09:24 AM   #2
CorneliusRox
 
CorneliusRox's Avatar

Name: CorneliusRox
Title: Seasoned Rookie
Status: Not Here
Join Date: Dec 2012
Location: Minneapolis, MN
Member`s Gallery
Posts: 3,515
Curious as well. I looked into this a long time ago and didn't find an answer.
__________________
Corey - BSME
Thumper - '97 12V Michigan Rust Bucket
Ares - '10 Rust-Free Family Hauler
  Reply With Quote
Old 08-06-2018, 10:24 AM   #3
iride813
 
iride813's Avatar

Name: iride813
Title: Green Behind the Ears
Status: Not Here
Join Date: Mar 2018
Location: Tennessee
Member`s Gallery
Posts: 36
Anyone??
  Reply With Quote
Old 08-06-2018, 12:48 PM   #4
mfsuper90
 
mfsuper90's Avatar

Name: mfsuper90
Title: 300ft is all I need
Status: Not Here
Join Date: Feb 2013
Location: Southeast ohio
Member`s Gallery
Posts: 733
I tried machining a set once, they were too hard for the cutters i had. But we only have old school tools, so I’m sure a nice carbide insert would do the trick
__________________
í82 300D benz Bosch MW turned up, HX30, W/A Intercooler
MF Super 90 various odds and ends done. Farm stocker
MF 98 3-71 screaming jimmy. Needs N90's. Another farm stock
'14 Ram Anarchy EFI, G56
  Reply With Quote
Old 08-06-2018, 12:55 PM   #5
Redrider2911

Name: Redrider2911
Title: Too Much Time
Status: Not Here
Join Date: Nov 2015
Location: Yakima, WA
Member`s Gallery
Posts: 702
I machined the shoulder thinner on a set once to more closely resemble am 024. I believe if you are going with full cuts, then im sure you just turn the shoulder all the way off to where the shank is smooth.... I would think within .001 would be even enough.
__________________
49 Willys Pickup. 5600lb. 94 12 valve. 47RH, low stall single disc converter. 3.54 posi rear. 35" tires. 64mm HE351ve, S475 (75/96/1.32), A/W Intercooler. AFC mods. 5x16s. 191 DVs, 180 pump. 23*. 85psi. Build Thread
  Reply With Quote
Old 08-06-2018, 01:40 PM   #6
1320Cummins

Name: 1320Cummins
Title: 2G Collector
Status: Not Here
Join Date: Feb 2009
Location: Houston TX
Member`s Gallery
Posts: 78
Maybe this helps a bit...
__________________
01 2500 QC SWB Laramie Sport 47RE 4X2- BD R700s, F1 Mach 7s, HD 181/210, Quad ADR 4K/S03 , Dunrite TC & VB. Interior
- Alpine, Focal, JL & Dynamic Control.
02 3500 QC SLT 48RE 4X4- II PS62/K31, DD 200s, TST Comp/EZ, Dunrite TC & VB, Alpine, Infinity & Dynamic Control.
  Reply With Quote
Old 08-08-2018, 07:18 AM   #7
iride813
 
iride813's Avatar

Name: iride813
Title: Green Behind the Ears
Status: Not Here
Join Date: Mar 2018
Location: Tennessee
Member`s Gallery
Posts: 36
We have cutters. I’ve made them all into full cut. Was just wondering if they were supposed to be a certain diameter or if they just need to have the shoulder turned down flush.
  Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:18 AM.

 


Powered by vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2018, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com