Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
Diesel Conversions Powerplant swaps, Repowers, etc. |
10-01-2017, 10:01 AM
|
#1
|
Name: 1972RedNeck
Title: Green Behind the Ears
Status: Not Here
Join Date: Sep 2014
Location: Townsend, MT
Member`s Gallery
Posts: 93
|
6466 Swap - Need Flywheel Help
So I picked up an Ex-fire truck - 1965 GMC 5000 6X6 powered by a 351 V6. When I got it, it had a plate on it so I tried to haul some hay with it.
Since second gear low range won't get much hay hauled in a timely manner, I took the pate off and put a flatbed on it.
Tried to use it to haul water to the sprayer, but a 1600 gal tank of water will bring it to it's knees as well (high gear in low range). At first, I wanted to put a 6BT in it, but since the engine compartment is a fair bit bigger than a pickup, I figure why not go bigger. A DT466 would fit about perfect, but then I would be in danger of my green underwear getting in a wad. A little searching and I picked up a Deere 6466 out of an 8820 combine for cheap. 220 HP (eventually will end up around 300 HP) and only 4,500 hours, it should make a top notch engine for the old 6X6.
I found an SAE 1 flywheel housing off of a pumping unit engine which will mate to my RTO 12513 (will get made into an RTOX 12513 with triple overdrive) but I haven't been able to come up with a flywheel. The pumping unit and combine flywheel don't have a clutch disc surface - they just have the ring gear and the driveshaft bolts on with the crank bolts.
I have a 4440 tractor flywheel that is made for a clutch, but the bolt pattern is not a standard SAE pattern.
Does anyone know of an SAE flywheel that will fit these John Deere engines?
__________________
1990 F350 4X4, Sterling 10.25, Dana 60, E4OD
4BTA, HX30W/H1C Compounds, 5X16 Injectors
Quote:
Originally Posted by longhorn859
Assemble, floor it.
|
|
|
|
10-02-2017, 05:15 PM
|
#2
|
Name: Gorrila550
Title: Rookie
Status: Not Here
Join Date: Dec 2014
Member`s Gallery
Posts: 25
|
you may need to have it redrilled for a sae clutch
__________________
1999 Ford F550 1993 5.9 cummins with A518 trans
|
|
|
10-02-2017, 10:03 PM
|
#3
|
Name: 1972RedNeck
Title: Green Behind the Ears
Status: Not Here
Join Date: Sep 2014
Location: Townsend, MT
Member`s Gallery
Posts: 93
|
Quote:
Originally Posted by Gorrila550
you may need to have it redrilled for a sae clutch
|
I could, but the surface for the clutch disc is deeper than any standard SAE clutch.
Surely some application used an SAE flywheel?...
__________________
1990 F350 4X4, Sterling 10.25, Dana 60, E4OD
4BTA, HX30W/H1C Compounds, 5X16 Injectors
Quote:
Originally Posted by longhorn859
Assemble, floor it.
|
|
|
|
10-05-2017, 09:03 AM
|
#4
|
Name: 1972RedNeck
Title: Green Behind the Ears
Status: Not Here
Join Date: Sep 2014
Location: Townsend, MT
Member`s Gallery
Posts: 93
|
Any leads on an SAE flywheel?
__________________
1990 F350 4X4, Sterling 10.25, Dana 60, E4OD
4BTA, HX30W/H1C Compounds, 5X16 Injectors
Quote:
Originally Posted by longhorn859
Assemble, floor it.
|
|
|
|
10-05-2017, 09:14 AM
|
#5
|
Name: J-Pipes
Title: Too Much Time
Status:
Here
Join Date: Jan 2012
Location: Ohio
Member`s Gallery
Posts: 4,560
|
Not really a Deere guy, but very knowledgeable on tractors, try checking with Chris, signature600, or something like that on here.
Sent from my SAMSUNG-SM-G930A using Tapatalk
__________________
2000 Dodge ext cab short bed, 6spd.
|
|
|
10-05-2017, 01:53 PM
|
#6
|
Name: 1972RedNeck
Title: Green Behind the Ears
Status: Not Here
Join Date: Sep 2014
Location: Townsend, MT
Member`s Gallery
Posts: 93
|
Quote:
Originally Posted by J-Pipes
Not really a Deere guy, but very knowledgeable on tractors, try checking with Chris, signature600, or something like that on here.
Sent from my SAMSUNG-SM-G930A using Tapatalk
|
Will do, thanks.
__________________
1990 F350 4X4, Sterling 10.25, Dana 60, E4OD
4BTA, HX30W/H1C Compounds, 5X16 Injectors
Quote:
Originally Posted by longhorn859
Assemble, floor it.
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 05:05 AM.
|