Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
LB7 GM Duramax Discuss the 1st Generation Duramax here |
08-30-2017, 09:07 PM
|
#1
|
Name: Duramaxfan03
Title: Green Behind the Ears
Status: Not Here
Join Date: Jul 2016
Member`s Gallery
Posts: 42
|
How to get more HP/TQ?
Hey guys, just wondering if you had any tips or tricks to squeak out any more hp out of an LB7 that is limited to a stock turbo, that mainly does sled pulling. The truck already has up pipes, manifolds, larger injectors, fass system, CAI, bigger intercooler tubes and the easy stuff like that. I've heard of people hogging out the mouthpiece of the turbo with a Dremel for more air but haven't looked into it much. Any little tips or tricks would be awesome, just looking for anything that may give a little bit of an edge over the other guys. Thanks guys!
__________________
S&B CAI, MBRP intercooler tubes, PPE manifolds and up-pipes, profab turbo horn, MBRP downpipe, 5" straight exhaust, 10mm cp3, Fass 150 lift pump, 60% over injectors, studs, Custom traction bars, G2 tie rods, kryptonite center link, built trans & T-case
|
|
|
08-30-2017, 09:10 PM
|
#2
|
Name: Duramaxed
Title: Green Behind the Ears
Status: Not Here
Join Date: Apr 2014
Location: Granbury, Tx.
Member`s Gallery
Posts: 88
|
Spray it.
__________________
Lly built motor, s475, dual pumps, 80 over injectors, built trans.
|
|
|
08-30-2017, 09:20 PM
|
#3
|
Name: CorneliusRox
Title: Seasoned Rookie
Status: Not Here
Join Date: Dec 2012
Location: Detroit, MI
Member`s Gallery
Posts: 4,154
|
Send the turbo out to have some larger wheels put in it.
__________________
Corey - BSME '21 Tesla Model 3 Perf
'22 DMax AT4 2500
|
|
|
08-30-2017, 09:21 PM
|
#4
|
Name: Duramaxfan03
Title: Green Behind the Ears
Status: Not Here
Join Date: Jul 2016
Member`s Gallery
Posts: 42
|
For my class we are not allowed any injectables and we have to use a stock wheel
__________________
S&B CAI, MBRP intercooler tubes, PPE manifolds and up-pipes, profab turbo horn, MBRP downpipe, 5" straight exhaust, 10mm cp3, Fass 150 lift pump, 60% over injectors, studs, Custom traction bars, G2 tie rods, kryptonite center link, built trans & T-case
|
|
|
08-30-2017, 09:22 PM
|
#5
|
Name: Duramaxfan03
Title: Green Behind the Ears
Status: Not Here
Join Date: Jul 2016
Member`s Gallery
Posts: 42
|
Might be a really dumb question but would putting in a larger exhaust housing wheel in do me any good at all?
__________________
S&B CAI, MBRP intercooler tubes, PPE manifolds and up-pipes, profab turbo horn, MBRP downpipe, 5" straight exhaust, 10mm cp3, Fass 150 lift pump, 60% over injectors, studs, Custom traction bars, G2 tie rods, kryptonite center link, built trans & T-case
|
|
|
08-30-2017, 09:24 PM
|
#6
|
Name: Duramaxed
Title: Green Behind the Ears
Status: Not Here
Join Date: Apr 2014
Location: Granbury, Tx.
Member`s Gallery
Posts: 88
|
Stock size wheel or completely stock? Stock Batmo wheel. Also truck is tuned right? I didn't see any of your info on.
__________________
Lly built motor, s475, dual pumps, 80 over injectors, built trans.
|
|
|
08-30-2017, 09:27 PM
|
#7
|
Name: TheBac
Title: UPS guy
Status: Not Here
Join Date: Oct 2009
Location: Mid Michigan
Member`s Gallery
Posts: 2,344
|
Profab intake horn, intake Y bridge and downpipe.
Port/polish the exhaust side of the turbo. If you can get away with it, port/polish compressor side, too and add Wetzel wheel.
Sportsman CP3 so you can fully use those 60%. Bet your rail pressure drops like a rock right now.
Better valvesprings/pushrods.
Update tuning to optimize everything at higher rpm to help internals live.
Then start saving for rods. Its not a question of "if", but "when" you'll be rebuilding.
__________________
Tom
"BBT" -- 2003 GMC CC/SB 4x4 12.14@111.15
"KLESHAY" -- 2000 C5 Corvette -- the toy
2017 Buick Regal 2.0T -- the DD
Last edited by TheBac; 08-30-2017 at 09:29 PM.
|
|
|
08-30-2017, 09:44 PM
|
#8
|
Name: Duramaxfan03
Title: Green Behind the Ears
Status: Not Here
Join Date: Jul 2016
Member`s Gallery
Posts: 42
|
Has to be the stock wheel. They check after every event. Are there any write ups on porting/polishing the turbo or anything like that? The truck has a 10mm cp3 in it now with 65% injectors
__________________
S&B CAI, MBRP intercooler tubes, PPE manifolds and up-pipes, profab turbo horn, MBRP downpipe, 5" straight exhaust, 10mm cp3, Fass 150 lift pump, 60% over injectors, studs, Custom traction bars, G2 tie rods, kryptonite center link, built trans & T-case
|
|
|
08-30-2017, 09:44 PM
|
#9
|
Name: Duramaxfan03
Title: Green Behind the Ears
Status: Not Here
Join Date: Jul 2016
Member`s Gallery
Posts: 42
|
Plan was to do some more this winter and then take the truck to duramax tuner to get a vehicle specific tune done on it.
__________________
S&B CAI, MBRP intercooler tubes, PPE manifolds and up-pipes, profab turbo horn, MBRP downpipe, 5" straight exhaust, 10mm cp3, Fass 150 lift pump, 60% over injectors, studs, Custom traction bars, G2 tie rods, kryptonite center link, built trans & T-case
|
|
|
08-30-2017, 10:54 PM
|
#10
|
Name: JWhite
Title: Trained monkey
Status: Not Here
Join Date: Aug 2009
Location: F Burg Ohio
Member`s Gallery
Posts: 1,817
|
If it needs a legit stock wheel, a port / polish job on the turbo is about all you can do.
I recommend Danville Performance for tuning.
__________________
GMC with a LiLLY
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 06:29 AM.
|