Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
6.0 Powerstroke Discussion of the 03-06 6.0 |
02-28-2016, 10:52 PM
|
#21
|
Name: Bigrednightmare
Title: Diesel Enthusiast
Status: Not Here
Join Date: Jul 2014
Member`s Gallery
Posts: 106
|
And in response to your post I have not thrown a single part in the truck and I don't plan to do so until I'm fully confident in what I do will fix the issue, I can't speak for the other shops and why they did what they did but I do agree that it's a little ridiculous.
__________________
Ppumped 02
|
|
|
02-29-2016, 07:37 AM
|
#22
|
Name: PRINCETON_JAKE
Title: Too Much Time
Status: Not Here
Join Date: Jan 2010
Location: Princeton Minnesota
Member`s Gallery
Posts: 1,125
|
So the shop that found the "gas" in the fuel was the shop that originally put a used Motor in 3 months prior?
__________________
silver 2006 ram 2500 4x4, crew cab short box, 48RE auto with "stuff" done, 5.9 with more "stuff" done
|
|
|
02-29-2016, 01:55 PM
|
#23
|
Name: biggy238
Title: Too Much Time
Status: Not Here
Join Date: Aug 2008
Location: Just North of Wrong
Member`s Gallery
Posts: 10,862
|
Quote:
Originally Posted by wise guy
not to be a dick but all three shops need to start DIAGNOSING not guessing. this is exactly why the 6.0 gets bad reputation!!!! valve job, injector job, and trans overhaul for misfire .....Really?????? 6.0 is as about as simple as it gets on a modern diesel..... proper tools and procedures will identify problem quickly. So called" DIESEL SHOPS" give these trucks bad name . fuel pressure ? under load ? volume? quality? oil full? quality? misfire under load should be easy to identify with ids every misfire will be logged single cylinder? multiple cyl misfire? say has new injectors new oem ? or rebuilt by hillbilly bob? 05 federal trucks will not have maf if harness has takeout for iat sensor. Why are we questioning the cam and crank sensor 10 minutes with 2 channel lab scope will tell you if they are good or bad. F@ck it just throw another 100 bucks in parts maybe this will fix it.
|
Because unplugging a sensor and ohming is cheaper than a ****ing lab scope you silly cock smoker.
And yes. The 6 liter is a piece of ****. No one gave it a name It didn't earn. As with all of the engines Navi has pedaled since the early 2000s. If a modern diesel engine can't push 500k without big iron being pulled off, it's a bag of dicks.
Sent from my XT1053 using Tapatalk
__________________
Check out @bdmaximusworx
05.5 Campanella White TDi Jetta 5spd 45.5MPG
-Little Sexy
'10 Silver F250 CCLB 4X4 6.4L cummins Swapped
Insta @trash.panda250
|
|
|
02-29-2016, 02:18 PM
|
#24
|
Name: biggy238
Title: Too Much Time
Status: Not Here
Join Date: Aug 2008
Location: Just North of Wrong
Member`s Gallery
Posts: 10,862
|
In light of the other posts you made, I took more offense than perhaps I should, but that condescending bull**** you posted is not warranted.
It is simple enough to say to investigate a sensor, utilizing whatever tools you have, and suggest what need be used.
Sent from my XT1053 using Tapatalk
__________________
Check out @bdmaximusworx
05.5 Campanella White TDi Jetta 5spd 45.5MPG
-Little Sexy
'10 Silver F250 CCLB 4X4 6.4L cummins Swapped
Insta @trash.panda250
|
|
|
03-08-2016, 08:51 PM
|
#25
|
Name: renegade
Title: Rookie
Status: Not Here
Join Date: Jun 2015
Member`s Gallery
Posts: 2
|
I am a Certified Master auto and truck Tech, light and heavy duty, with 40+ years of experience (fortunately now retired) and you seem to have the correct approach to fixing the problem, yes some times you just have to throw a part at something, but only after due diligence. The prior shops may be good shops but they seem to be very big on if we replace enough parts maybe it will work. And to the poster that said you could test the sensors with an ohmmeter, sometimes, sometimes not, a sensor can ohm out within spec but still show up bad on a lab scope, especially when it seems to be a heat related issue. Worked on a 6.0 once that had a very intermittent miss when warm, somebody had put a plastic washer on the ground pigtail for the FICM, when it got warm and the stars aligned it missed, hit a bump, miss went away, hit another it came back, found that one by accident.
|
|
|
03-08-2016, 09:29 PM
|
#26
|
Name: will24
Title: That guy
Status: Not Here
Join Date: May 2010
Location: South Williamsport, PA, Elverson, PA and Luray, VA
Member`s Gallery
Posts: 2,719
|
I'm going to be the outcast here... What oil and how many miles??
Sent from my flashscan v2
__________________
|
|
|
03-08-2016, 09:31 PM
|
#27
|
Name: will24
Title: That guy
Status: Not Here
Join Date: May 2010
Location: South Williamsport, PA, Elverson, PA and Luray, VA
Member`s Gallery
Posts: 2,719
|
And is it aerated.
Sent from my flashscan v2
__________________
|
|
|
03-11-2016, 06:54 AM
|
#28
|
Name: vinniehobart
Title: Diesel Enthusiast
Status: Not Here
Join Date: Apr 2013
Location: Valley Center
Member`s Gallery
Posts: 151
|
so a 03 motor in a 05 truck. what was all swapped over? did they just extend the ICP sensor to reach the HPOP? What was all used for the 03 swap? PCM? etc.
__________________
2003 Ford 6.0 CCSB Lariat Gearhead Tuning,S362FMW 62/68/.83,Driven Diesel, Irate Diesel, ISSPRO, S&B. 493 fuel 541 on
2006 F250 6.0 single cab gearhead tuning SX-E S369 RCD 250/150 injectors, Thumper 2, stock 224k mile trans!! 7.90 @89MPH!!
|
|
|
03-11-2016, 06:56 AM
|
#29
|
Name: vinniehobart
Title: Diesel Enthusiast
Status: Not Here
Join Date: Apr 2013
Location: Valley Center
Member`s Gallery
Posts: 151
|
also, what FICM is being used?
__________________
2003 Ford 6.0 CCSB Lariat Gearhead Tuning,S362FMW 62/68/.83,Driven Diesel, Irate Diesel, ISSPRO, S&B. 493 fuel 541 on
2006 F250 6.0 single cab gearhead tuning SX-E S369 RCD 250/150 injectors, Thumper 2, stock 224k mile trans!! 7.90 @89MPH!!
|
|
|
03-11-2016, 07:27 AM
|
#30
|
Name: proctors garage
Title: Diesel Enthusiast
Status: Not Here
Join Date: Oct 2011
Member`s Gallery
Posts: 159
|
I'm just getting over the headache of a truck that sounds just like this. I checked and rechecked everything and finally hit the wall. It started great and idled smooth nothing on contribution test. I had a custom tune written for the ECM that raised ICP pressures. and it helped the miss that would start at about 2000 rpm. it was worse under load. this truck also had just had a set of injectors installed about 3500 miles earlier. injectors came from a man well know in the 6.0 injector building world. After the tune helped the miss I went ahead and replaced injectors again and the problem was fixed. I'm pretty sure this was caused from dirty fuel after I removed the fuel filter/pump on the frame to clean it out it was pretty overwhelmed.
|
|
|
03-11-2016, 07:35 AM
|
#31
|
Name: 95cummins5.9
Title: Old man ***** gossiper
Status: Not Here
Join Date: Jun 2012
Location: U.S.A
Member`s Gallery
Posts: 4,720
|
Quote:
Originally Posted by biggy238
Because unplugging a sensor and ohming is cheaper than a ****ing lab scope you silly cock smoker.
And yes. The 6 liter is a piece of ****. No one gave it a name It didn't earn. As with all of the engines Navi has pedaled since the early 2000s. If a modern diesel engine can't push 500k without big iron being pulled off, it's a bag of dicks.
Sent from my XT1053 using Tapatalk
|
|
|
|
03-23-2016, 11:04 PM
|
#32
|
Name: Bigrednightmare
Title: Diesel Enthusiast
Status: Not Here
Join Date: Jul 2014
Member`s Gallery
Posts: 106
|
The problem has yet to be solved, lots of checking and coming up dry, the only thing I keeping seeing happen is the icp voltage jumps all over the place when the stumble happens, but the pressure does not change and will stay steady , but I'm not sure that's what causing it , this thing has already had the icp sensor and harness replaced atleast twice, so I'm not sure. I may take a video tomorrow and post it
__________________
Ppumped 02
|
|
|
03-23-2016, 11:06 PM
|
#33
|
Name: Bigrednightmare
Title: Diesel Enthusiast
Status: Not Here
Join Date: Jul 2014
Member`s Gallery
Posts: 106
|
Quote:
Originally Posted by PRINCETON_JAKE
So the shop that found the "gas" in the fuel was the shop that originally put a used Motor in 3 months prior?
|
Yes the shop that put the engine in found gas in the system after the truck died going down the interstate
__________________
Ppumped 02
|
|
|
03-23-2016, 11:07 PM
|
#34
|
Name: Bigrednightmare
Title: Diesel Enthusiast
Status: Not Here
Join Date: Jul 2014
Member`s Gallery
Posts: 106
|
Quote:
Originally Posted by vinniehobart
so a 03 motor in a 05 truck. what was all swapped over? did they just extend the ICP sensor to reach the HPOP? What was all used for the 03 swap? PCM? etc.
|
I'm unsure of how they went about doing the swap. I think they used everything from the 03 but I'm not 100%
__________________
Ppumped 02
|
|
|
06-03-2016, 09:43 AM
|
#35
|
Name: L6powered
Title: Too Much Time
Status: Not Here
Join Date: Apr 2009
Location: Miami, Fl.
Member`s Gallery
Posts: 676
|
any updates????
|
|
|
06-03-2016, 11:13 PM
|
#36
|
Name: Ackerdiesel
Title: Too Much Time
Status: Not Here
Join Date: Nov 2010
Location: Western KY
Member`s Gallery
Posts: 1,086
|
Quote:
Originally Posted by will24
I'm going to be the outcast here... What oil and how many miles??
Sent from my flashscan v2
|
Quote:
Originally Posted by will24
And is it aerated.
Sent from my flashscan v2
|
Even fukkin better what kinda low pressure oil do you have. I'd almost bet it's not electrical
Ryan
__________________
04.5 2500 CR Built by Cruel Intentions Diesel with the help of:
D&J Precision Machine
S&S Diesel Motorsports
BD Diesel Performance
Diesel Performance Converters
Pro Street Diesel
Drivelines Plus
Done Right Diesel Performance
Firepunk
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 06:56 AM.
|