Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
Exterior Care Wash, Wax, Paint, Body, Buffing, and Polishing. |
11-11-2014, 03:24 PM
|
#21
|
Name: zfaylor
Title: Comp Diesel Sponsor
Status: Not Here
Join Date: Nov 2010
Location: P-TOWN!, Indiana
Member`s Gallery
Posts: 5,024
|
Quote:
Originally Posted by inline6359
I shouldnt be down to bare metal in many spots. Mainly if i weld up the screw holes for the fender flares. That should be all the metal i see. Can i prep those areas with the epoxy primer then do sandable on the rest and over the epoxy primer on the fenders?
|
You sure can. Make sure to coat the backside of those welds with something to avoid rusting from the inside out!
__________________
2015 half ton heavy chevy
81 Fairmont LS project
Many yard ornament projects...
North American Turbo
|
|
|
11-11-2014, 03:49 PM
|
#22
|
Name: inline6359
Title: Microwaving cats since 01
Status: Not Here
Join Date: Aug 2006
Location: Western PA
Member`s Gallery
Posts: 2,043
|
Roger that. I will probably start with something like the bed. And go from there. Lots of flat area and i can take it off the truck. One thing that is encouraging is sonic blue metallic is what it is. No color matching or hues to worry about. Or so i would think.
__________________
"If at first, the idea is not absurd, then there is no hope for it"-Einstein
|
|
|
11-11-2014, 03:53 PM
|
#23
|
Name: zfaylor
Title: Comp Diesel Sponsor
Status: Not Here
Join Date: Nov 2010
Location: P-TOWN!, Indiana
Member`s Gallery
Posts: 5,024
|
Quote:
Originally Posted by inline6359
Roger that. I will probably start with something like the bed. And go from there. Lots of flat area and i can take it off the truck. One thing that is encouraging is sonic blue metallic is what it is. No color matching or hues to worry about. Or so i would think.
|
Just make sure you stir the paint extremely well to make sure you get even paint if you will be painting the bed separate from the truck. Also remove the bed from your spray area when you spray the truck so overspray doesn't ruin the job on your bed. Like I mentioned earlier ask your supplier if a drop coat is recommended on their metallics.
__________________
2015 half ton heavy chevy
81 Fairmont LS project
Many yard ornament projects...
North American Turbo
|
|
|
11-11-2014, 04:05 PM
|
#24
|
Name: whitneyj
Title: still in pieces
Status: Not Here
Join Date: Jan 2012
Location: Mayville, WI
Member`s Gallery
Posts: 822
|
you have to sand the backside of your welds too if accessible. The discoloration doesn't like to hold onto primers.
__________________
Toy-less and lost
|
|
|
11-15-2014, 02:20 AM
|
#25
|
Name: Nor'Easter
Title: Too Much Time
Status: Not Here
Join Date: Nov 2012
Location: Maine
Member`s Gallery
Posts: 947
|
I use an LPH400 for base and clear. Harbor freight guns for epoxy primer and high build primer.
SPI epoxy sands great, I don't really like high build as it tends to be softer.
__________________
Mike
Stacked silencer rings.
1957 Cummins Power Wagon
2014 Regular Cab G56
|
|
|
11-15-2014, 03:31 PM
|
#26
|
Name: SuperSonic
Title: El Vato
Status: Not Here
Join Date: May 2006
Location: In a Barn
Member`s Gallery
Posts: 2,036
|
Fwiw, sonic blue has two different pearl additives in it.
It lays down pretty nice though.
I Use two different guns, one for primer and one for sealer/base/clear.
Like it has been mentioned, make sure you have plenty of supply air and make sure to use a good dryer/filter setup before your gun.
You can go the cheaper route on most of your primer and base products but make sure you use a good clear and make sure you apply enough of it that you can wet sand out any minor imperfections without getting into your base.
__________________
COMPDEX
Quote:
Originally Posted by longhorn859
Sometimes I feel like giving up....then I remember I have a lot of motherfukkers to prove wrong.
|
|
|
|
11-17-2014, 11:11 PM
|
#27
|
Name: inline6359
Title: Microwaving cats since 01
Status: Not Here
Join Date: Aug 2006
Location: Western PA
Member`s Gallery
Posts: 2,043
|
Quote:
Originally Posted by SuperSonic
Fwiw, sonic blue has two different pearl additives in it.
It lays down pretty nice though.
I Use two different guns, one for primer and one for sealer/base/clear.
Like it has been mentioned, make sure you have plenty of supply air and make sure to use a good dryer/filter setup before your gun.
You can go the cheaper route on most of your primer and base products but make sure you use a good clear and make sure you apply enough of it that you can wet sand out any minor imperfections without getting into your base.
|
Elaborate on the pearl additives? These need added to the basecoat??
Thanks for all the info guys? I plan on spending the coin on good primer, clear, and base. Also on a filter setup.
__________________
"If at first, the idea is not absurd, then there is no hope for it"-Einstein
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 12:56 AM.
|