No instructions for fleece controller..?

B

buzzin1/2dozen

New member
Just like the title reads. I didnt get the instructions for my fleece controller to run on an 04 cr. I know these things are pretty much self explanatory but being that I'm not very familiar with cr's I'm not sure on the connections. I know the lead that hooks to the controller on the turbo isnt quite right, as I'll have to shave the plastic guides in order for it to connect. But my question is for the three leads hanging together, where do they go. I'm gonna guess map, but that will only use two of the three. Second question is for the red and black wires, can I just use ignition Pwr and ground or is that somethin specific as well. I know all this seems very ignorant to post but I have no way of contacting fleece today and need to get the truck out of here. Any help would be huge and greatly appreciated. I'll pm my # to anybody who could help. Thanks,
 
(765) 676-5063 i googled fleece performance, its not hard to find a phone number these days unless your brain dead, but anyhow here's the number they will help you
 
Listen jack wagon, your attempt at sarcasm has left you in a vulnerable position to be made the brain dead retard you seem to know so well. Read the post and don't comment on it until your capable of comprehending what it's saying. The post was put up today, in this country it's Sunday. Sunday means closed. Closed means I'll be unable to contact them. Post specifically reads "today". Go fuk yourself you ignorant prick.
 
buzzin1/2dozen said:
Listen jack wagon, your attempt at sarcasm has left you in a vulnerable position to be made the brain dead retard you seem to know so well. Read the post and don't comment on it until your capable of comprehending what it's saying. The post was put up today, in this country it's Sunday. Sunday means closed. Closed means I'll be unable to contact them. Post specifically reads "today". Go fuk yourself you ignorant prick.
Click to expand...

:eek:wned: But you need to put this in the tech section or dodge performance, pm a mod.
 
Last edited:
I appreciate the advice. This is gonna sound dumb, but can I transfer this thread to there or do I new to just repost. Never had to do this before. Thanks
 
buzzin1/2dozen said:
I appreciate the advice. This is gonna sound dumb, but can I transfer this thread to there or do I new to just repost. Never had to do this before. Thanks
Click to expand...

You can't transfer it yourself, I see that wunderwood is on right now, pm him, he should be able to move it.
 
I appreciate all the help guys. The 3pin connector I supposed to plug into the can bus signal, but that still leaves the other two which are supposed to piggy back the map sensor. I'm wondering if I have the wrong harness since the two connectors are Completley different from the maps. It's all hooked up now and I can controll the exhaust brake fine. And when the dial reaches 100% it seems to do the same thing at 0% fueling. The test drive however was horrible. I made a total of 10lbs of boost and a high pitch squeal at WOT. No good. Anyhow the turbo seems ok by play and egt's never went over about 800.. Wtf. It has to be this map pigtail. The diesel power ad was helpful but didn't reveal everything, but I really appreciate it. Not sure what's next, maybe trim this grey hair...
 
The website says all 3 wires hook to the datalink connector. I do not think that is the CANBUS but the proprietary Cummins connector. That is a 3 pin plug coming out of the harness down at the ECM.
 
Ok, Im hooked into that connector, just didnt know the name. There is only one female connector on the fleece controller and it has to fit the engine connector. Phucked up thing is on all three of my fleece connectors there are only 2 wires fed into the three wire connector. The engine connector is three wire. My other two fleece connectors are both male. I've looked and looked but cannot find any alternative to using these connectors.

Did just notice that of the two (at this point unused) male connectors the pins inside are male on one and female on the other. Man the instructions would be awesome.
 
I'm pressty sure this harness is for an 02. I don't have an 02 to verify my point but hear me out. The 02's also have a similar connector behind the vp and down a little bit with a dummy cap on it that would fit my fleece harness now. That would mean I'd have to use one of the male fittings on that data connector. The other male and female connector would be used as the map fooler, as they are the same style plug in as the 02's map. Man I hope I'm wrong but that certainly makes sense.

Of this entire system I can only find one three pin connector that fits my harness. I believe on an 02 there'd be two..
 
Can anyone tell me the name of the guy on here who works for fleece? I know it's late but if he's got a minute maybe I could pm him and just resolve this issue. I'm over it
 
You must log in or register to reply here.
Back
Top