Advertisement
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Home Who's Online Today's Posts HP Calculator CompD Gift Shop Mark Forums Read
Go Back   Competition Diesel.Com - Bringing The BEST Together > Vendor Row > Sponsor Forums > Diesel Performance Converters
Register Members List Timeslips EFI Live Library Invite Your Friends FAQ Calendar Mark Forums Read

Closed Thread
 
Thread Tools
Old 04-29-2015, 10:14 PM   #1
Asher

Name: Asher
Title: Rookie
Status: Not Here
Join Date: Mar 2015
Member`s Gallery
Posts: 9
trying to hold 2nd gear (48re)

This is a early 04 truck with the mechanical throttle cable...

I got the transmission back into the truck, with the new parts and DPC triple disc, its an amazing difference. But I am having a tuning issue that I don't know how to tackle. During moderate to heavy throttle (and/or stock programming) the tranny works great, runs through all gears just like it should... but during normal city driving (very light throttle) it's almost completely skipping second gear and going into 3rd... I take off, in first and it runs out like it should maybe 30ft then hits 2nd only rolls about 4ft and then into 3rd. Just like pulling up to a intersection and making a right turn, take off in 1st, but before I have completed the turn I have jumped from 1st, into 2nd, and immediately into 3rd when exiting the intersection. Or another case sitting at a stop light in traffic behind cars, the light turns green cars start rolling, I start to go (but the cars aren't taking off as fast) so I have to lift the throttle, the truck will go from 1st, into 2nd for a split second, and then into 3rd, then traffic starts going so I apply "light" throttle and the truck just holds in 3rd and builds speed.

I have adjusted the kick down cable to shift later, but I'm not sure this is the answer because 3-4 shifts are just fine if not drawn out a little more then I would like. I think I have a lot of things working against me... one of the biggest seems to be that the "smarty tune" in the truck allows such little throttle travel that tranny is almost skipping 2nd because it is not recognizing any load...

So is there a way to draw out 2nd gear in light throttle applications without effecting the timing on the rest of the gears?

The tranny has a transgo shift kit in it built to the instructions, except for the pressure screw turned in 2 turns for a little more pressure, a 4.3 apply lever, sonax piston, etc...

Any advise would be greatly appreciated...
 
Old 04-29-2015, 10:18 PM   #2
Asher

Name: Asher
Title: Rookie
Status: Not Here
Join Date: Mar 2015
Member`s Gallery
Posts: 9
Just to be clear the truck is NOT 1-2 shuttle shifting, once it goes into 3rd it stays there unless you apply a far amount of throttle... I don't mind this tranny acting like it is, I just don't want to want to burn it up but making 3rd gear do most of the work...
 
Old 05-16-2015, 09:50 AM   #3
59turbo

Name: 59turbo
Title: Diesel Enthusiast
Status: Not Here
Join Date: Jul 2010
Member`s Gallery
Posts: 155
Try to go a little tighter on the throttle valve cable (kick down cable). The 3-4 shift is computer controlled via apps position.
__________________
2004 2500 Shortbed reg cab 2wd, Goerend triple disc, Fleece holset, BBi stage 1.5, Fleece 10mm cp3, FASS 150. Best ET to date 11.36@120 with firepunk tuning.
 
Closed Thread

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:11 PM.

 


Powered by vBulletin
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2006 - 2024, CompetitionDiesel.com
all information found on this site is property of www.competitiondiesel.com