Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
07-08-2015, 08:04 PM
|
#21
|
Name: DPC
Title: Diesel Enthusiast
Status: Not Here
Join Date: Sep 2009
Location: Elgin, OK
Member`s Gallery
Posts: 218
|
Hope you figure it out, I have had the same issue with no solution. Changed about everything you can think of. Does your vibration seem to get worse when it gets colder, 45* and below?
__________________
2006 QCSB Cummins EFILive, Built Tranny, HE351cw/S480FMW, 60hp inj, 85%cp3
2003 ECSB Duramax EFILive, Built Tranny, GT4094R,PPE Dual Fuelers,RDL Headers and Up-pipes
620HP 1170TQ @ BDP 12-12-09
|
|
|
07-19-2015, 05:42 PM
|
#22
|
Name: davem3261
Title: Too Much Time
Status: Not Here
Join Date: Oct 2009
Member`s Gallery
Posts: 258
|
I haven't had time to mess with it. My wife is driving it the rest of the week. I'm anxious to tear into it
__________________
05 2500HD 6.0 Texas speed Cam and heads, S475 3000 stall.
Ex money pit truck '04.5 2500 SLT QC SB 4x4
4.10's , HE351/S475 twins, BMS 100hp, FASS, ATS dual cp3, Fat Shaft Billet Trans, 5" aluminum driveshaft SOLD!
|
|
|
07-19-2015, 05:59 PM
|
#23
|
Name: madmikeismad
Title: So mad
Status: Not Here
Join Date: Dec 2009
Location: Newalla, OK
Member`s Gallery
Posts: 14,347
|
Literally just had this issue, but it was ujoints in the rear shaft. Another friend had the same issue with new ujoints, and it turned out they just weren't "seated" properly, and the straps weren't quite on right. Might pull the shaft and rotate 180* also.
EDIT: To completely rule out the rear shaft/diff/axles, pull the driveshaft, run just the front axle on jackstands. That might narrow it down to the trans/tcase.
__________________
Mike Hill
Last edited by madmikeismad; 07-19-2015 at 06:03 PM.
|
|
|
10-28-2015, 07:18 PM
|
#24
|
Name: davem3261
Title: Too Much Time
Status: Not Here
Join Date: Oct 2009
Member`s Gallery
Posts: 258
|
Update
I finally got around to tear into the rear end. There was next to no preload on the bearings. In a certain spot it would jump up to 60 in lbs. I took it apart gears were fine. Bearings looked fine too. I went ahead and replaced all the bearings. After that no more vibrations! I never would have thought that was the issue but it was.
__________________
05 2500HD 6.0 Texas speed Cam and heads, S475 3000 stall.
Ex money pit truck '04.5 2500 SLT QC SB 4x4
4.10's , HE351/S475 twins, BMS 100hp, FASS, ATS dual cp3, Fat Shaft Billet Trans, 5" aluminum driveshaft SOLD!
|
|
|
10-28-2015, 07:19 PM
|
#25
|
Name: davem3261
Title: Too Much Time
Status: Not Here
Join Date: Oct 2009
Member`s Gallery
Posts: 258
|
Update
I finally got around to tear into the rear end. There was next to no preload on the bearings. In a certain spot it would jump up to 60 in lbs. I took it apart gears were fine. Bearings looked fine too. I went ahead and replaced all the bearings. After that no more vibrations! I never would have thought that was the issue but it was.
__________________
05 2500HD 6.0 Texas speed Cam and heads, S475 3000 stall.
Ex money pit truck '04.5 2500 SLT QC SB 4x4
4.10's , HE351/S475 twins, BMS 100hp, FASS, ATS dual cp3, Fat Shaft Billet Trans, 5" aluminum driveshaft SOLD!
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 10:39 AM.
|