Advertisement |
|
|
|
If this is your first visit, be sure to check out the FAQ by clicking the link above.
You may have to register before you can post: click the register link above to proceed.
To start viewing messages, select the forum that you want to visit from the selection below.
|
12-17-2018, 06:38 AM
|
#1
|
Name: coorsman2005
Title: i like beer
Status: Not Here
Join Date: Jun 2011
Location: blackwell,ok
Member`s Gallery
Posts: 784
|
3rd gen g56 rear drive shaft
Like title says. Need rear drive shaft for 3rd gen g56 4x4 qcsb. Going back to manual
__________________
08 3500 qcsb 6.7 6 speed manual, valair DD, all deletes efi live, arp studs&rocker studs, Vulcan hg w/orings, max spool valve springs, max spoolpush rods, SB66.
2008 megacab 4x4 dually 12v build in progress
1990 2wd d100 4bt nv5600 vailair single disk in progress
|
|
|
12-25-2018, 04:44 AM
|
#2
|
Name: coorsman2005
Title: i like beer
Status: Not Here
Join Date: Jun 2011
Location: blackwell,ok
Member`s Gallery
Posts: 784
|
Anyone
__________________
08 3500 qcsb 6.7 6 speed manual, valair DD, all deletes efi live, arp studs&rocker studs, Vulcan hg w/orings, max spool valve springs, max spoolpush rods, SB66.
2008 megacab 4x4 dually 12v build in progress
1990 2wd d100 4bt nv5600 vailair single disk in progress
|
|
|
12-25-2018, 12:46 PM
|
#3
|
Name: Mark Nixon
Title: No Savior among the flesh
Status: Not Here
Join Date: Feb 2009
Location: Brownville, Nebraska
Member`s Gallery
Posts: 8,676
|
Might help if you gave the center-to-center distance on the u-joint cups (not weld to weld), then those with a few lying around may decide to check lengths.
Mark.
__________________
If you or I did business like the PEOPLE in government do business, we'd be put in jail. Government is coercive.
Anarchy: The state of existence where there are no masters & no slaves. Therefore, Anarchy means the ABSENCE OF SLAVERY, or, in other words, FREEDOM.
|
|
|
12-25-2018, 08:01 PM
|
#4
|
Name: coorsman2005
Title: i like beer
Status: Not Here
Join Date: Jun 2011
Location: blackwell,ok
Member`s Gallery
Posts: 784
|
I'll throw a tape on them tomorrow
__________________
08 3500 qcsb 6.7 6 speed manual, valair DD, all deletes efi live, arp studs&rocker studs, Vulcan hg w/orings, max spool valve springs, max spoolpush rods, SB66.
2008 megacab 4x4 dually 12v build in progress
1990 2wd d100 4bt nv5600 vailair single disk in progress
|
|
|
12-25-2018, 08:03 PM
|
#5
|
Name: coorsman2005
Title: i like beer
Status: Not Here
Join Date: Jun 2011
Location: blackwell,ok
Member`s Gallery
Posts: 784
|
All I know now is roughly 50 " center center of the welds. Know that's the right way to measure. But its close
__________________
08 3500 qcsb 6.7 6 speed manual, valair DD, all deletes efi live, arp studs&rocker studs, Vulcan hg w/orings, max spool valve springs, max spoolpush rods, SB66.
2008 megacab 4x4 dually 12v build in progress
1990 2wd d100 4bt nv5600 vailair single disk in progress
|
|
|
12-26-2018, 08:39 AM
|
#6
|
Name: Cummins6.7trip
Title: Green Behind the Ears
Status: Not Here
Join Date: Aug 2015
Location: Pa
Member`s Gallery
Posts: 76
|
I have the factory one from my truck 08 qcsb. It’s just the shaft no slip yoke the piece that bolts the rear axle.
|
|
|
12-26-2018, 08:49 AM
|
#7
|
Name: Cummins6.7trip
Title: Green Behind the Ears
Status: Not Here
Join Date: Aug 2015
Location: Pa
Member`s Gallery
Posts: 76
|
It was a 4x4 g56 did a 48re swap is the only reason it was removed.
|
|
|
12-26-2018, 08:59 AM
|
#8
|
Name: Mark Nixon
Title: No Savior among the flesh
Status: Not Here
Join Date: Feb 2009
Location: Brownville, Nebraska
Member`s Gallery
Posts: 8,676
|
Quote:
Originally Posted by coorsman2005
All I know now is roughly 50 " center center of the welds. Know that's (not) the right way to measure. But its close
|
I'll assume you meant "NOT the right way to measure", so I corrected it.
The only reason I wanted you to clarify the u-joint center-to-center distance, is that I have found that the u-joint ends can be different depths.
So, while the tube weld lengths can be the same, the overall length can change due to the u-joint ends being deeper or shallower.
Mark.
__________________
If you or I did business like the PEOPLE in government do business, we'd be put in jail. Government is coercive.
Anarchy: The state of existence where there are no masters & no slaves. Therefore, Anarchy means the ABSENCE OF SLAVERY, or, in other words, FREEDOM.
|
|
|
12-28-2018, 06:55 AM
|
#9
|
Name: coorsman2005
Title: i like beer
Status: Not Here
Join Date: Jun 2011
Location: blackwell,ok
Member`s Gallery
Posts: 784
|
Yes mark that's what I meant. Haven't looked at this thread for a few days.
CUMMINS6.7. What you want for that shaft. I can reuse my yoke or yokes.
__________________
08 3500 qcsb 6.7 6 speed manual, valair DD, all deletes efi live, arp studs&rocker studs, Vulcan hg w/orings, max spool valve springs, max spoolpush rods, SB66.
2008 megacab 4x4 dually 12v build in progress
1990 2wd d100 4bt nv5600 vailair single disk in progress
|
|
|
12-28-2018, 07:03 AM
|
#10
|
Name: coorsman2005
Title: i like beer
Status: Not Here
Join Date: Jun 2011
Location: blackwell,ok
Member`s Gallery
Posts: 784
|
Hell I just reread that. I assume your truck had a 2 piece shaft. Is that right?
__________________
08 3500 qcsb 6.7 6 speed manual, valair DD, all deletes efi live, arp studs&rocker studs, Vulcan hg w/orings, max spool valve springs, max spoolpush rods, SB66.
2008 megacab 4x4 dually 12v build in progress
1990 2wd d100 4bt nv5600 vailair single disk in progress
|
|
|
12-28-2018, 07:05 AM
|
#11
|
Name: 06 DIESEL
Title: Dead Eye Firearms LLC
Status:
Here
Join Date: Sep 2007
Location: Airville, PA
Member`s Gallery
Posts: 5,122
|
I have one sitting in my garage from an 06. If you pay the ride plus $100 you can have it, it is complete with carrier bearing and all, was removed from friends truck when went to one piece shaft, not sure of condition of joints without checking.
__________________
Travis
My rig - 2021 Mega 3500 SRW
My Classic - 79 Chevy Silverado
Quote:
Originally Posted by RonA
Trucks are like women. Sometimes you just need to spend money on them to keep them happy.
|
|
|
|
01-06-2019, 01:39 PM
|
#12
|
Name: coorsman2005
Title: i like beer
Status: Not Here
Join Date: Jun 2011
Location: blackwell,ok
Member`s Gallery
Posts: 784
|
Thanks to Cummins6.7trip. I now have a drive shaft on the way.
__________________
08 3500 qcsb 6.7 6 speed manual, valair DD, all deletes efi live, arp studs&rocker studs, Vulcan hg w/orings, max spool valve springs, max spoolpush rods, SB66.
2008 megacab 4x4 dually 12v build in progress
1990 2wd d100 4bt nv5600 vailair single disk in progress
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -5. The time now is 04:07 AM.
|