Recent content by chevydiesel

S400 T6 Turbine housing 1.10 A/R for the 74/83 turbine wheel. Brand new. $100 shipped

Bare new turbine housing for Borg Warner S400 Turbo with the 74/83MM turbine wheel (known as the 74mm wheel). It's a T6 1.10 A/R $175 Shipped, or: Will trade for a T4 .90 or 1.10 A/R Turbine housing for same wheel.

Feeling out Possible sale of Turbo It's an Engineered Diesel S300 frame turbocharger with the following specs: 66MM 6-Blade Billet Compressor Wheel 68MM Turbine Wheel .70 A/R T3 Turbine Housing Wastegated Spring-Gate Wastegate Controller 2nd Gen Cummins Configuration Holset/v-band compressor...

Looking for a T4 Footed either single entry or divided 1.00 A/R Turbine housing or .91 A/R (actually like to have both) for the S300 frame turbo's that is cut for the 71mm turbine wheel. No gate, just regular housing. HX40 Flat 4" downpipe flange also a plus. PM whatcha got.

I need a center bearing housing for an S364 turbo or an S366 turbo. Got a blow up that didn't tear up the bearing housing? That's what I need, bearings aren't part of this equation (as long as the bearing bores a good). I have one that the bearing housing got broken out where the thrust bearing...

Here is the wastegated turbo from a Banks Sidewinder turbo kit for the IDI 6.9 and 7.3 Diesels. The turbo is in good shape and is only missing the center section clamp because some booger eater "lost" it. I was going to put this on a Banks 6.2L Diesel but lost interest in the truck. I'm...

This is the TE06H-24V Turbo that Banks uses on their 7.3L IDI Sidewinder kit that's the "wastegated" turbo that the Ford guys really seek out. This turbo also wound up on some of the 6.2 and 6.5's. This turbo has been used on 6.2's equipped with the Banks turbo kit. This turbo supplies more...

I need a 2nd gen 71mm turbine wheel S300G turbine housing (wastegated) in the 80ar or 14cm. Figured there would be a blown up turbo somewhere... This would be the Super Phat Shaft Housing or BD Super B Special Housing. Thanks!

Nuff numbers? Looking for a used S300 turbine housing that's cut for the 71mm inducer exhaust wheel. I have a 12cm that has the full marmon 4" outlet, I want one that's cut for the HX40 flange already. I'll take another 12cm or 14cm wastegated housing, again cut for the 71mm wheel. If someone...

Looking for an HY35 turbo with the tiny 9cm turbine housing. I'm not in need of just any HY either, looking for the one that essentially looks like an HX35, the one without the integrated 90 bend cast on the compressor housing, and still has the 2.5/3.0 turbine/exhaust discharge too, not the...

Looking for a used (but not used up this time) FASS 150 GPM pump filter system. I've got a FASS 150/150 and FASS wants and arm and a leg for a replacement motor because mine failed, and it wasn't the brushes in the motor, it seized. I also can't get just the motor without it being "retrofitted"...

Got a Garrett HT3B Turbo that has a 22cm non-divided T6 turbine housing on it. I was thinking that this would make a great housing for quick spooling in a compound turbo setup. Not sure if I want to sell, just generating interest. I don't REALLY know what it's worth, just was on the turbo that...

I'm looking for a turbine wheel for a HT3B turbo, I have one, it's just a little melted, just discovered this tearing down the turbo acquisition. Everything else in the turbo was good, just needs the wheel. The turbine wheel inducer size is unknown (the melted part) but the exducer size is...

Looking for the smaller S300 unit for a tow rig. The specs are as follows 57/65/14. Usually they're called the HTBG or BD's Super B, and it's a S300g turbo with the smaller 57mm compressor wheel. Got one? Thanks fer the read!

Looking for a good used 14cm - .80 a/r Turbine housing that will directly fit the Industrial Injection S300 65mm turbine wheel sized turbo. I've got the .70, and would like the ability of swapping housings for comparison, spoolability/EGT's, etc. Buying new may just be too far out of the budget...