Recent content by jones95runner

Not sure how these will show up. But the way we did ours. All the bed frame is made out if alum. I can pick it up with 1 hand to tilt it, then I have a bar to hold it. I had air cylinders on it but wasnt really worth it. The cab, all the frame the cab needed was From the back of the front door...

5x30 Hart's dual feed truck Injectors 1500 Shipped obo Schieds 5x38 dual feed ih Injectors for Cummins 1500 obo 5 new regrind cams 232/254(good oem head pulling cam) $400 a piece Hart's hx60 3.0 mwe. 25cm Wheel has got Into cover will come with new Cummins rebuild kit. $1500 Cast s475 chra...

Going to part out. Would like to keep body and frame/axles together. Will seperate the rest. sheetmetal rear, military front with locker light hubs and willwood brakes, coilovers 20k 4 disc crower clutch setup, clutch can, profab reverser and a motor plate for 6.7 cr 5k obo 4 cut tires and...

Cast wheel s480. Does have some shaft play but came off running tractor. $500obo Forced inductions s488 v2 cover latest wheel. Bearings are like new. Might have 10 runs on it. Wheel has some debris wear where the mwe groove is will send pics. $1200 obo Vs turbo s488. Nice shape all around...

Cast wheel s480. Does have some shaft play but came off running tractor. $500obo Forced inductions s488 v2 cover latest wheel. Bearings are like new. Might have 10 runs on it. Wheel has some debris wear where the mwe groove is will send pics. $1200 obo Vs turbo s488. Nice shape all around...

Listing again. Have a 12cyl p pump built by schieds, injection lines, 2:1adapters and a schieds adjustable gear for a cummins. just refreshed and tested at schieds. Think it did 1400cc or so. Was asking 3k for setup but open to any offer or trades. Can send pictures of setup. 731-445-0591.

3 seasons since fresh. still runs great. Just went to 14mm reason for selling. $3000 shipped. Call or text. 731-445-0591

2 used and 1 new. No twist in splines. They were in a work stock puller. $400 shipped for all 3. Text 731-445-0591 for pics

I am like you though, It is neat but to me a nitrous run for a few secs isn't much to impress me.. make 3500hp on fuel for 15 sec in a common rail and it'll be something that peaks my intrest.

Hamilton solid block, never ran. fire rings cut in block.-$3000 Hamilton high swirl head bare.-$1300 13mm harts ag pump with adjustable gear.-$3500 harts 5x25 billet injectors.-$1500 older schieds alum runner intake. $400 NEW t6 comp steed. $600 slightly used(no color change) t6 stainless...

Listing again. Have a 12cyl p pump built by schieds, injection lines, 2:1adapters and a schieds adjustable gear for a cummins. Looking to get $3,000. Can send pictures of setup. 731-445-0591.

12v, Going a different route and no longer needed. $1600 shipped. 731-445-0591

S464 with billet wheel, 360 thrust, 83mm turbine, 1.10 t4 housing. Turbo is tight, no bearing play. $800 shipped. 731-445-0591.

I have 3 37 spline yukon axles for a dana 80, 39.5" length. Also have a welded 37 spline carrier I will throw in. $600 shipped for it all. 731-445-0591

Like new t4 steed manifold. 24v straight, nongated $500 shipped 731-445-0591