Recent content by rkadcock

Helping a friend sell his old turbo and manifold. The manifold is a 2 piece DAP common rail style manifold. The turbo is an industrial Injection silver 64 (64/74/ 14cm). Turbo was gone through by Industrial roughly a 1000 miles ago. Includes stainless braided oil feed and and lines. He's...

I'm selling my blue 7" mitre Old Skool Fab hoodstack due to a change in plans. It's brand new, never even mounted. It is 9" tall at the top of the mitre. Asking $450 shipped. Pictures are from when I got it and just placed on top of hood

I have an extra SFI approved billet flex plate from Firepunk that has never been ran since I already had a billet flex plate on the truck. $300 shipped. I can send pictures if wanted.

Selling my old SDX 5x14 Injectors that I have laying around. I bought them from a member here a few years ago and since having them put roughly 3000 miles on them. $450 obo shipped.

I have an extra set of brand new unopened set of ARP rod bolts (part # 247-6303). $150 shipped. Also, have a set of stock 12v rod bolts. They came with the hardened rods that were purchased from CPP. I haven't had a chance to measure them for stretching but can if needed. $40 shipped Lastly I...

I'm getting ready to install my compounds on my 12v but had a few questions. I'm running a "side by side" setup with a 63/68 over a s488 on a Steed Speed manifold with a JGS 40mm wastegate. For the boost line which goes to the wastegate, I was originally going to weld a bung into the...

I have a few compound parts that I found while cleaning out my shop and no longer need since I went a different route with my compounds. New 2nd Gen Source Automotive s300 to s400 Hot Pipe - $250 New Source Automotive Straight Oil Drain Nipple - $10 Used Side by Side Compound Oil Feed and Drain...

Selling the 4k GSK out of my 12v. They have roughly 10,000 miles on them. Selling since I swapped them out for a 5k GSK. $60 shipped

I've got a set of 94-98 tear drop style Recon smoke cab lights that have been laying around my shop since I took them off a few months ago when I switched to the 99-02 style cab lights. These are about 3 years old. The bulbs are included but thanks to Recons flimsy wiring I hard wired them so...

I have a "new" FCA for a 5.9 CR. I bought it from Rocky Mountain Cummins roughly two year ago and ran it for maybe 3-5 miles before figuring out that the FCA wasn't my problem. Since then its been sitting in a locker in my shop taking up space since their is no returns on electronics. $40 shipped

Selling my dual valve cover breather since I've moved onto a one piece valve cover and have no need for this anymore. Includes 2 new valve cover gaskets but doesn't come with the bolts since they were stripped out when I bought it used about a year ago. $150 shipped to your door

Somewhere down the road my billet tappet cover has started dripping a little oil from the bottom of it. Its not a bad leak, but it leaves a drop here and there and I can definitely confirm the leak is from the cover. Question is since I can't get a hold of the people (Side cover) who built it...

I finally got my motor back together from the build and now I've run into issue. When I start it, it starts right up; but it starts at about 600 RPMs then idles up to around 1000. After that it has a fairly heavy white/blue smoke from the exhaust that wreaks of oil and can bring tears to your...

I need to get a tach pickup spacer for my 97 dodge so I can finally finish putting it back together since I apparantly missed place mine when we tore my engine apart last year. Local Cummins store said they couldn't get it so I'm turning here for help. But theirs a catch, I need it ASAP, pretty...

Long story short, Ive got a 5.9 FCA from trying to diagnose some fueling issues in my new truck. I bought it from Rocky Mountain Cummins about 2 weeks ago, installed it, got about 1/2 a mile on it then my truck died again. So ended up getting a CP3 and a bag of parts and using the FCA that it...