Search results

I have a service truck that I just got done changine the oil on, now I have a leak out of what looks to be a oil temp sensor on the passanger side of the pan. I have called the local big ford truck shop and they can not find a part number, Can anyone help me with this, or at least give me a name...

Just woundering how many of you have had to change your injector line, and how many times have you. I have changed mine now 3 times ( one a year) and all of them are blowing out the crimp at the head. I am always way away from home when it happens and I just hope it would spray enough on the...

I have a p pump front cover and gears except the pump gear. This is all off of a 4bt That is a p pump 4 cyl. Its too hard to find a 4cyl p pump so I figured I could help someone and get some money to buy the front gears and cover to put a ve pump on it. I'll throw it out there for 800, make in...

Does the 518 behind a v8 have the same bell housing as the cummins did in the first gens?

While on my way to work this morning my truck started to miss. Pulled over and found I had a code p2149. Did some reading on it and found that the fuel injector group 2 circuit. So I ordered and got a new valve cover gasket hoping this would fix it. This did not. I am look for a schematic or...

How many people have had to replace injector lines on the cr engines. I am replacing my 2nd injector # 4 line. I was woundering if it a big problem or am I the only one?

I just grounded pin 22 and mine still wont work. I took the smarty off. I have my clutch switch went out and instead of replacing it, I just put the wires together. Not sure what the problem is. Do I need to fix my clutch switch? Does the smarty matter?

Im looking to get a ecm pin so I can ground out the system to use my cruise controll to bump up my idle from 1000 rpm.

Im running the south bend 3850 pressure plate (thought I would do more pulling) in my daily driver, this past week it quit disengaging and I found the rod had threaded in. At least I think that was the problem. Now when I take off it is hard to put the trans in 1st, 2nd, and revers. all other...

The truck has a blown rear axle, and the cab is not the in the best shap. The door hinges are worn and the drivers door doesn't latch. Engine runns, manual trans, needs a clutch. Good for parts. Asking 2500. Near Kansas city.

I have a guys tow truck in my shop that when it runs for 30 min to an hour it starts to choke down he says, it won't run right. He has taken it to international cause it is in a tow truck and they cant seem to figure it out. They replaced a fuel regulator, he has replaced a few injectors with...

Is the 6.7 cp3 able to be modified like the 5.9. I am able to buy two 6.7 cp3 cheap and lookin to modify it so I don't have my truck down. Any help would be great.

A friend of mine put a fass on his 05, went to put his smarty on a lower level and it got to about 60% and threw a code error 42 and wont download anything. We were able to get it to stock. But now it wont download to any of the seetins. Why would this happen?

Does anyone have pics or have a write up on staking the valve seats on a cr engine?

What is a stock cr engine head cfm with a stock cam? I just want a base so I can figure how much fllow I want and match a cam to what I already have done to my truck.

I am lookin to do a port and polish on the head, would it be work on a cr block?

Missing the pyro lead. Asking $350

Asking 500. Missing the pyro lead. Ran good.

After to talking for a short bit to cam builder, it sounds like a 24v cam is better then the stock cam. He metioned something like the exhaust is advanced 10 degrees. i know a custom grind would be better but Im looking at the options. If anyone has any suggestions please share them with me.

After to talking for a short bit to cam builder, it sounds like a 24v cam is better then the stock cam. He metioned something like the exhaust is advanced 10 degrees. i know a custom grind would be better but Im looking at the options. If anyone has any suggestions please share them with me.