Search results

Nearly brand new, I just got it on Tuesday and decided I should have got a NF. It's been mounted and I've fired about 30 rounds. MOA reticle $875 shipped

I had to take my pickup back to the dealer for a recall fix so I figured that's a good time to have them install cab lights also. They call me today and say the middle 3 cab lights can be installed but the 2 outside lights can't because there is a steel reinforcing plate behind the headliner...

I'm no longer using this for work so it's up for sale. -224k miles -6.7/Aisin -8k miles on front tires -2k miles on rear tires -12' box with roll up door -aluminum pipe/lumber rack (built by Protech when they still had a custom shop) -Protech boxes behind cab on both sides -deletes with HPP...

My 2014 3500 is at a dealer getting some service and they tell me the rear diff has a bunch of water in it. They pulled it apart to inspect and said the pass side bearing spun so I need a new axle housing, and then told me it's $5500 just for the part plus install. And they're on backorder...

I'm planning on getting rid of my box truck and getting a pickup and trailer to replace it. I know what I'm getting for a pickup but I don't know much about trailers. I'm thinking a 8x16 would be plenty big. I want it to have a pass side man door, and I'm undecided on the double doors or ramp...

To be able to upload photos easily? Take facebook for example. It takes about 1 second on there, but on here it's like a whole big 9 step process. Almost all the forums I'm on are like this one as far as that goes, and I've always wondered why.

Set of 6, around 10k miles, set at 260bar. $700 shipped lower 48

Just like the title says, for sale is an .83 T4 housing for a 68mm turbine with HX40 outlet. I'd like to see about 250 shipped. Will trade for a T3 housing or for reloading supplies/equipment.

What's everyone doing for the crankcase ventilation with a billet cover? I was just going to run a hose out of each of the holes to a TEE and then to the ground. I'm pretty sure that would lead to a lot of oil dripping though so I need other ideas to allow pressure out but keep oil in.

Looking for EV2 0-2000 Pyro, 0-60 boost, and full sweep trans temp. I want factory match to an 06 chevy 2500.

I got a Hamilton 188/220 that I pulled after it was installed incorrectly and ate into the cam bearings in the block. All the bearings measure dead on at 2.125", and I talked to Zach yesterday and he said to put it in a lathe and if necessary, knock down any high spots (there are none) and then...

I pulled a 188/220 out of an engine that had the cam installed incorrectly as it started eating the bearings in the back of the block. The cam had about 1500 miles on new tappets. I measured all the bearings on the cam and they were ALL 2.125". The lobes that I checked were the same also. My...

$750 picked up or $800 shipped Selling a Borg 63/68/.83 t4 turbo with a Stainless Diesel t3/t4 adaptor. Has a 3rd Gen compressor housing and hx40 exhaust housing. 30-40k miles on it. Buyer pays shipping. Text or PM me for pics. 360 702 8570

Which color name indicates someone that can open an old thread for me?

Over this past winter I pulled my engine for a reseal as it was leaking pretty bad. I decided it would be a good idea to put in a cam and new lifters at that time. I did that and followed the manufacturer's instructions for break in exactly. Lots of Royal Purple assembly lube and cranked without...

If I have .046-.048 valve recession on the intake side of the head and .025-.026 piston protrusion, will I be ok to run the 188/220 with a .020 thicker head gasket?

I pulled my engine recently to reseal it and do a cam. Everything looked fine until I got the oil pan off and found what appear to be two of the piston squirters laying next to the drain plug. Black plastic hollow pieces about 1.25-1.5" long, maybe 3/16" diameter. I'd post a pic but I'm on my...

Some time here in the near future I'm going to do some comparing on a set of 6x13 nozzles honed to 80lpm and some SDX 5x18. Both will be set at 260 bar and be run in a VE engine with a 63/68/.83 T4, built auto, and all the normal pump work. I want to know what kind of info people want to see...

I've got an EV2 0-2000 pyro and I can not, no matter how many times I try, make it work consistently. The needle jumps and bounces all over. I've had it work correctly for a few months here and there, but then I drive down a nasty bumpy road and it starts acting all crazy again. I'm pretty sure...

I need the chrome ring with 6 screw holes and all associated parts that would have fallen out. Got to work the other day and the whole setup was missing. Or if anyone has a part number for a stock replacement that'd be nice also. The part I'm looking for is whats sticking out of the hole in the...