Search results

1998 Dodge Ram 2500 4x4 Regular cab long bed 12V Cummins CPP 5x14 injectors with pop pressures set correctly by D&W Diesel 100cc 7mm DV's from Weston 4k GSK 18* timing Haisely Billet tappet cover BD Super B Special turbo (63.5/72/14) BD three piece exhaust manifold S&B Cold Air intake Cooler...

The other night I noticed a slight rattle on acceleration only from a stop. It doesn't happen in park or neutral only in gear. I adjusted the valves just to make sure they are okay and everything is good there. The only other change would be I installed a Tork-Tek ofv. It was a non...

I'm looking for the intake plate with the removable grid heater. Mine is the all one cast piece and I'd like to find the two piece style. Preferably with an operation grid heater as well. Thanks.

These are the stock 181's out of my 180 pump. That have 250K miles on them if it matters to you. $100 shipped and they are yours.

Looking for a billet Flexplate for the 47RE in my 98 12V truck. I am running a Goerend converter if that makes a difference and let me know if I need a spacer. If I might I'd rather have it and not need it than find out while I'm doing it and not have one. Thanks.

I'm selling my CPP 7x14 12V injectors. These are just to big for my application. They fuel hard and the truck put down 383/1022 with the HX35. I need something a bit smaller. I will trade for a new (slightly used) set of 370's, some 5x14's or sell them outright. I paid $525 for them and...

I'm going to re-torque my stock head bolts and have searched and read plenty of threads for three days now but one thing has me intrigued. The torque sequence. I have seen there are guys that just take any one bolt out at a time, clean and re-torque, some that follow the Cummins sequence but I...

I am looking for a set of head studs for my '98 12V. A1 or ARP. If I remember right A1's don't require the rockers to be milled but need bottom tapped? I just need the 12mm versions for some peace of mind. Phil

I installed a Super B Special along with the BD exhaust manifold on my truck this weekend. I understand my cruising (at 65) EGT's are going to be a bit higher with the B than the HX35 as the turbine and housing are bigger.... 650* vs. 750* but my WOT EGT's haven't dropped as I was expecting. At...

Just wondering what you guys have found were the limits for the 241DLD t-case and Dana 70 rear axle. Mine are both in good condition but I want to start pulling and drag racing here once in a while....couple times a year at most. Truck put down 383hp and 1022tq at a dyno recently and I have a...

Looking for a set of 215 injectors. Will buy or trade for the 370's I have now. 370's work great just want to go a bit smaller to cut down on the heat for my stock charger.

I had my trans rebuilt a while ago and upgraded the most of the wek links that I could afford. Suncoast H/D Extreme rebuild kit, billet input and a Goerend converter. I didn't have the money for a VB from Goerend so I had a transgo kit installed. TFOD2 IIRC. Anyway at part throttle it shifts...

I picked on of these up for cheap and had it listed for sale on here and learned a lot....I talked to Mark at CDS about this thing. The one I have is a 63/71/19. Mark has a 17cm housing that he trade me for my 19cm + a little $. He also has all the adapters to bolt this right on my '98 12V...

I have heard this is a good upgrade for the Powerstroke guys so I figured I would post it here too: I have a brand new Holset H2E and I am looking to sell. I was going to put it on my truck but I am being told it might be a little big for me so if someone here can use it I'll sell it instead...

I have a brand new Holset H2E and I am looking to sell. I was going to put it on my truck but I am being told it might be a little big for me so if someone here can use it I'll sell it instead of bolting it up. It's a 63/71/19 model - T4 foot and has a little bit of shelf wear. I'll take $700...

I have a brand new Cummins 12V head for sale. Fully dressed with 60 pd springs (Exhaust) and new valves. I have a full set of rockers and stands along with lifters as well and a set of ARP head studs (Slightly used - 2 dyno runs then pulled for 14mm). This would be great for someone wanted to...

Rob Watkins AKA Maxtorq from Performance Car and Truck is a thief. If this is not the right place can a mod please move this.... Back in Septmeber I ordered a header from Rob. He never delievered it to me. 3 months and nothing but a bunch of excuses was all I recieved. He claimed the coating...

How many GPH do we need for our trucks for a certain power level? I have seen this posted by Lowfly from FASS: 95 GPH - Good for up to 450-500 HP 150 GPH - Good for up to 650-700 HP 180 GPH and above will feed anything else. Now from my drag racing gasser info i know you usually you take HP...

I have a question for those more in the know than I. Right now I have an S300 62/65/14 sitting on the bench. It is rebuilt and has a new turbine wheel....ready to roll. With some reading I have done I think this might be a bit to small for my 500-600 hp goals. I have the opportunity to sell this...

I have my 4K kit in and all is great except whe I set the Cruise. I get a slight surge when i set the cruise and then while running down the highway I'll feel a slight surge in the seat of my pants and the boost gauge will move a couple pounds and then settle back down. I have the GSK set to...