Search results

Here's my run from Friday night. Enjoy http://www.youtube.com/watch?v=PsMaENY3vCo

Anyone know when this event is coming up?

Guys, I will keep is short. I don't want to waste your time in case you aren't interested. I need votes on Facebook to help me win a clutch for a good friend in need. She is a diesel enthusiast mom in every sense of the word. Drives a diesel to pull her horses, and her two sons are big in to...

I had a couple of my good friends take my pulling truck to an event this weekend to pull. They took some on board videos for everyone to enjoy. Travis Tatsch 2.8/3.0 class 231ft 6th place http://www.youtube.com/watch?v=iwXVevyHUAU Matt Tatsch Open class 345 ft 2nd place...

This past week I built a set of ladder bars for my good friend on his 2011 Mega Cab. Here are videos of before and after. Also, I added a 2" spacer to the carrier bearing. It eliminated the shudder on take off even before the bars. (But after the first vid.) Thought y'all might like this...

Here are a couple of my open hooks from last weekend in Llano, TX. The first one was in 3rd gear. Went 246 and some change.The second was 4th gear, went 281 and change. My competition hook which I don't have a video of was a 4th gear hook, and I left the line at 3800rpm and it nosed over on...

Gentlemen, due to unforseen events, we will have to cancel the April 30th pull in Mineral Wells. We will be looking to reschedule the event in September. If you have any questions, you can contact myself, Gary, or Dan. Cody

Gentlemen, due to unforseen events, we will have to cancel the April 30th pull in Mineral Wells. We will be looking to reschedule the event in September. If you have any questions, you can contact myself, Gary, or Dan. Cody

Last pull of the year in Fredricksburg. Finally made my first full pull on the second video. I'm still light only weighing 6920. Haven't finished the Ford oval weight rack yet. I let off quickly on the first two hooks as I was kinda gun shy after the "De Leon incedent" where I grenaded the...

Well we went to the biggest pull in TX this weekend. The truck did very well, but the driver kinda sucked. LOL I should have lifted a few seconds earlier. Oops! Snapped the rear output shaft on the transfer case and shattered the tail housing. But the driveshaft loops did their job, and...

Guys I'm trying to help Billy and the B&L crew put on a sled pull in Llano on July 31st. This is going to be what we might call a "brush" pull. We will be using the sled that was used in Lomeda, and Johnson City antique tractor pulls. This pull is just going to be his first step into this...

Here's a few hooks from today. The shortest pull with the flame at the end was the winning hook. Then we hooked several times afterward just trying different things. But with hangin' weight, it just wouldn't pull 4th low. So these hooks were in 3rd gear. Enjoy...

Guys this will kinda be long winded, but bear with me. I was getting fuel a the station last night, and a Dodge truck pulls in with the cummins loping like a top fuel dragster. Once he stopped, and got out, the truck idled fine. Then I could hear the a/c kick on and it would lope out again...

I have a 72mm K31 with an Aurora 5000 center section, and 14cm exhaust housing. It's got a T3 foot. $850 shipped.

Guys, I came up with a way to remove those pesky axle nuts if you don't have the big socket. Drive Shaft U-joint straps!!!!!!! Install the U-strap with one leg in the axle shaft bolt hole, and the other leg inside the hub housing over one of the flats on the axle nut. Install one directly...

This video is the second hook for me. I was the first in the class and opted to rerun immediately. First hook I didn't hold the RPM's off the line and the turbo never lit. Second hook I held it at about 3200 rpms and slipped the clutch a little more. Ended up with 4th place with a pull of...

Okay everyone, pre-registration is open for the Spring Dyno Day in Buda, at American Racing Technology. This year my crew Death Row Diesel is co-sponsoring the event with the Central Texas Diesel guys. The date is Saturday April 4th and Big Dog event on Sunday the 5th. Dyno runs will begin at...

I can't get my signature to show up. And I'm not getting email notifications of thread subscriptions. What am I doing wrong.