Search results

Very informative, sends clear pictures, and very prompt shipping. Good doing business, Thanks Joe

Need one for an 01 2500hd dmax. It mounts under the cab and it has all the brake lines attached to it. Pretty sure its the same up to 07 classic. Joe

http://youtu.be/mfdkA366rpY

It was off of a 06 King Ranch 4x4 120K miles 3.73 gear ratio. truck was a rollover BUT not hit in the front. I bought the whole front frame rails and COMPLETE front axle assembly INCLUDING front drive shaft. But NO TRANSFERCASE. This setup could also be used to convert you 2x4 into a 4x4 since...

Got a 6 speed single disc clutch w/big input with 5k miles at 350 hp (01 24v) that was just refurbished by South Bend last week while I was picking up another clutch. They bead blasted everything, resurfaced flywheel, pilot bearing, relined the feramic side of friction plate, new throw out...

Got a 01 vp truck and its about 5 psi at idle and any throttle it drops to zero. So I was wondering if I could mount a replacement pump on the block and leave the intank pump in place. I was wondering if it could suck through it with no problem? Thanks Joe

Getting ready to bolt my head down with which will be the 3rd head gasket after stock one on my truck and taking a closer look at the studs, and they are pitted pretty bad. Only on the middle sized ones. And the long ones always stay oiled and the stubbys are fine. The studs look like a little...

Can this be done...got an 03 with a 7 pin FICM and i got a 4 pin FICM laying around and was wondering if it was worth swapping it in and getting it programed? thanks Joe

Need a full set. stock size or bigger it doesnt matter. just need to get them so i can finish my motor. Im goin 24v:rockwoot: thanks Joe

I have already searched and seen the tsb on contaminated coolant system, BUT it says NOT to proceed if it looks like the pics shown, which is thick light brown sludge. almost in a solid non flowing state. It doesnt say any thing about what do if it is. What are you supposed to do then?? I...

What: Dyno Day/grill out When: Saturday Sept. 25, 2010 10 am. Where: Northwest Diesel Service & Performance (about one hour east of Lansing) 20777 Osmus, Farmington Hills, MI 48336 Shop-248-957-8514 Cell-248-563-044zero How much: $65 for 2 runs Cant get too crazy around here because I...

The motor came out of a medium duty truck. UNKNOWN MILES. It has everything on it EXCEPT INJ. PUMP. YOU PAY SHIPPING HX35-$125 EX. Manifold (CR style)-$100 Computer-$100 Injecter lines-$100 VP Gear-$75 Stock cam w/gear-$100 Front timing covers-$100 SAE Bell housing-$200 monster alternator-$50...

Anybody swap a 02 disc 80 under a 98 12v 5sd where a drum 80 used to be? and if you have, did you change anything in the proportioning/metering valve department to accomadate the pedal feel? I'm doing this at the shop for a buddy and hes worrying himself sick over it. Also drum 80 and disc 80...

What is the most common thing to leak oil by the hpop cover on the 03 6.0l. have a buddy with a unmalested 03 155K mi. that never went to dealer for motor issues(perfect 6.0 huh?!). you could see oil leaking from the top center of block (under up pipes) and come down to drivers side. i took the...

i am selling these for my brother. These are a set of 8 used lb7 pistons that have been cleaned up with glass bead (tops only), and have been delipped and opened up to 2.6", and have been radiused with a .125 radius with nothing taken off the top. The pistons come out to be a 16.8:1 compression...

I am selling these for my brother, (he decided to take the $$$ plunge and buy some crowers) they are lbz connecting rods that have been cryoed and balanced to each other. i also have brand new con rod cap bolts still in the bag, that he will thow in with the rods. $275 shipped

Like title says, i am looking to trade my full cuts for 191's because i am sending my pump out to get benched soon and would like to have them before i send it out. thanks, Joe

So to the people that have been around a few times, what psi should be MAX for the 80/96/1.32 a/r in a twin setup under a 64/71/.70a/r (not sure on what cm that is)? THIS IS WHAT I AM GOING TO BASE ON WHETHER I PUT A EX. GATE ON IT OR NOT. specs: -7000lbs. truck -180 hp benched to what ever...

it came out a 95 2500 single cab 4x4. 12v-160 pump-195,xxx miles #100 fuel plate injectors of some sort (don't know) new hx35 also engine bay wiring harness w/ PCM MISSING PS PUMP AND LIFT PUMP 47rh w/ transfercase DLD and rear driveshaft. 36 gal. fuel tank Stock Innercooler EVERYTHING...

im selling it for a buddy. it came out a 95 2500 single cab 4x4. 12v-160 pump-195,xxx miles #100 fuel plate injectors of some sort (don't know) new hx35 also engine bay wiring harness w/ PCM MISSING PS PUMP AND LIFT PUMP 47rh w/ transfercase (not sure if its DLD or DHD) and rear driveshaft...