Search results

I have a set of four brand new injectors. These are the lucas (prince of darkness) that were bought from industrial injection. I'm pretty sure they are 4x.14 nozzles. $325 shipped.

Not sure if the rack is stuck or possibly something in the governor housing came loose. Either way selling as a core just incase it does end up being stuck rack. Truck stalled and would not start again. Had the truck sold so I just changed out the pump. It now has stock gov springs and 181 dvs...

Looking for a HY 35 in good condition and also looking for a stock dodge downpipe. Planning on running it on my 4bt. Thanks

85 Jeep CJ7. Cummins 4bt with approx. 90k miles on it. Only 2000 miles on the jeep since completion. Chevy adapter set to mate the 4bt to a Muncie SM465 4 speed transmission. Novak adapter mates the sm465 to the stock dana300 transfer case. 4 inch lift. Pre bent stainless brake lines. YJ roll...

Looking to replace a cracked exhaust housing on my silver bullet. Anyone know of a non wastegated housing that would fit it. I currently run it with the wastegate blocked and see about 50 psi max. Only reason for going this route is to save on cost.

Looking for a 2nd gen 24v head.

I have an 06 reg cab 48re 4x4 that Im wanting to swap for a g56 setup. The trans is stock for the most part. It has a garmon valvebody with billet gm style gov pressure solonoid, suncoast 3disc convertor, laminated flexplate, and a dtt shift enhancer. Drives fine just wanting to go to a stick. I...

Swapped out my stock valvebody today and installed a garmon one. When I try to put the shifter in park it still comes up on the dash as reverse. Its like the linkage is out of adjustment or something. If i get under the truck and push back on the lever coming out of the trans it will go into...

I rode in a friends truck that has a factory exhaust brake and when he uses it the truck downshifts with the convertor locked. Is there a different pcm in these trucks that causes that or an additional module installed from the factory? I am going to be adding an exhaust brake to my own truck so...

If anyone has one laying around or knows where to find one please let me know. It is the only part left I need to complete my driveline for my 1980 4bt powered CJ7. Thanks

Looking for either of the two but would prefer the NV only because it is easier to adapt onto my 4bt. I also need the bellhousing, clutch, shifter, adapter to go to a 4bt. It is going into a 1980 CJ7 with a dana 300 Transfer case.

ENGINE 913 (215hp) inj pump 4k gsk schied laser cut dvs 10 plate DDP4 injectors Piers intercooler BD Twin turbos 3 piece ATS manifold Head is studded and oringed water meth timing at 21* kdp tabbed TRANSMISSION new pump and case pro torque convertor Suncoast flexplate Suncoast extreme rebuild...

Just bought a 1980 CJ7 renegade. It has a chevy 350 in it right now. What is needed to swap in a 4bt. It has a rock crusher trans in it. Not sure if I can use that or not. Also anyone know what vehicles came with the 4bt that has the P pump.

I haven't hooked to a sled yet and before I do I am wondering if I should run 4H or 4L and if I should leave shifter in 1 2 od off?? Any help would be greatly appreciated.

I just got finished with this project. I removed the factory lift blocks in the rear of the truck and installed 2 inch ones. It makes the truck sit 1 inch higher in the back than the front and also the truck rides a lot nicer now. Before... After.... After with new wheels and tires...

Will a rear sliding window out of a newer say 01-02 ram fit into a 95. I like the cleaner look of not seeing the seal on the outer edge of the window?

Factory aluminum five spoke polished wheels off of an 06 2500. Two of the wheels have slight scuffs just in the clear coat. Not from a curb. From shipping. Only noticeable up close. Cooper STTs are 285/75/R17. Two are 60 percent tread and the other 2 are 50 percent tread. They should go another...

I have a set of 06' aluminum wheels with Cooper STT mud terrains mounted on them. The tires are about 2-50% and 2-60% tread. They have about 15k miles on them. Two of the wheels have slight scuffs in the clear coat that could be removed and recleared if needed. Includes 4 center caps. Local...

These are a little bit bigger than 191s. $200 shipped. Thanks

Bought these last year and had them in the truck for 2 months and went back to a 4k gsk. Don't need these any more. I don't know what there worth. Make me an offer. Thanks.