Search results

The block was bored .040 over and has fire ring grooves cut in the deck for rings in the block only, will need to be honed for new pistons will come with oil pan and pick up tube $300 balanced crank standard size bearings $300 USA rods with A1 bolts $200 Front gear housing for p-pump $150...

I am looking for a stock p-pumped 12v or 98-99 24v fuel filter housing. I am not interested in the newer 00 - 07 housing. Thanks

I have a brand new set of Putco Stainless fender trim for a 3rd gen Dually. the part number is 97303. I bought these about 6 months ago to replace the ones on my truck, But these don't cover enough area to cover up the marks from the old ones on my truck. I am asking $75 shipped. Attached is...

While driving my 98.5 this morning my oil pressure fell to 0 on the gauge cluster. I have a mechanical gauge in it also so I was able to verify it had oil pressure. Moments ater the Water in Fuel light came on. A short while after the truck started losing power. Everyonce in a while the...

This is the last of my parts forsale 95 12v IH casting block, that is bored .040 over. Has grooves cut for fire rings in the block only. Block is in good shape. Just decided to part out the whole motor. asking $500 12v crank ballanced and the crank gear is welded on, std size bearings $300...

I have a used set of Richmond Pro Series gears forsale for a Dana 60, 4.88 ratio. They have about 20 hooks on them. asking $150 shipped Also have a 1410 yoke spicer part number 3-4-5711-1x for a dana 60, comes with straps asking $45 shipped

I have a Brand New in the box B&M transmission temp gauge. It is part number 80212. I also have a B&M drain plug part number 80250 that is still in the package. Bought this a year ago and sold the truck before I put it in. They are $47 from summit for the gauge and the drain plug is $6.99...

I have the 12v I ran in my puller. It has 11 hooks on it since being gone through. Its a IH 12v block, was bored/honed 40 thou over. Haisley girdle, A1 14mm main studs, A1 H11 head studs, H11 rod bolts, Has Mahle pistons that were coated by swain tech, gold coat on top and teflon on the...

I have a Kennys 3 disc clutch for an nv4500. It is 4 seasons old and the diss are for an 1 3/8 input. Two years ago I resurfaced the wear plate in the flywheel and put two new discs in it. It has about 30 hooks on it since then. Total Im sure it has atleast 150+ hooks on it. It is in need...

I have a 1998 Dodge Ram Ext Cab long Box Frame that I was in the process of building a 3.0 Diesel Open driveline Pulling Truck out of. Frame was pretty much stripped, all factory Suspension mounts ground off. It has a welded in with ladder bar setup Rockwell H172 rearend in it that has been...

I have forsale a used dana 60 spool for 35 spline shafts, it was used in a drag car for 5 passes, then I bought it to put in the front of my puller. Asking $150 shipped Also have a grainger water pump part number 4P016, that flows 3800gph, that I used for my air to water innerooler setup...

Aermotive Pro Series pump, ran for 11 hooks, Just like new. These are $720 from Jegs and summit. Im asking $500 shipped. here is what Aermomotive says about them. -12AN inlet and outlet ports Includes two -12AN tapered flare fittings and O-rings Flow exceeds 1000 lbs/hour @ 13.5 volts/45 psi...

I have forsale 5" 6806 Autometer Diesel Tach. Was ran for one season. Works great. comes with an extra probe. Asking $250 shipped 100psi Isspro black face boost gauge. asking $40 shipped 2nd gen steering column single gauge mount. $25 shipped. 2 BFG 33x12.5x16.5 all-terrains that were on...

Forsale 12V Cylinder head. Intake cut off for ZZ fab intake. Water jacket is filled with Embeco 885 grout filler. Head was ported to pretty much the max it can be. I have flow sheets to go with. Will give out information to serious potential buyers. Has manley valve springs, 10 deg locks and...

I have a ring gear spacer for a dana 60 so you run run 4.56 and numerically higher gears on a 4.10 and numerically lower carrier. comes with the longer bolts also, ran for one season asking $30 shipped. Also have a dana 60 Welded carrier, for 4.10 and down, 32 spline. Asking $75 shipped. Also...

I have a 2wd Mainshaft for a nv4500, and a 2wd tailhousing forsale. I'd like $100 for the mainshaft and $100 for the tailhousing.

Does anyone have any contact information for a PPL Tech? I have looked on their website, but havent found anything other then a common email address, which I have emailed and havent recieved a response yet.

I have a used frozen boost water to air type 17 interooler was used for 11 hooks. Will come with 3.5 to 3 inch silicone reducers, and two 3.5 t-bolt clamps asking $225 shipped.

I have a Scheid 13mm p7100 with a rsv gov. Was built 2 years ago. 900cc's max and can go down to 300cc's. has external fuel screw, open rpm, 45psi return check valve, self contained oil. Only has about 25 hooks on it. Comes with adjustable pump gear and drive hub. Any questions feel free...

Flange yoke for 241DHD or DLD For stock front driveshaft $15 Stock 12v exhaust manifold $50 Stock air box for 2nd gen $20 Stock air intake tube for 2nd gen $15 Stock gauge cluster from 95 $30 PCM off 95 manual $75 Engine wiring harness off 95 manual $50 hx35 parts, i have everything, but the...