Search results

The wife said its time for me to clean the garage. head Gasket part number 4981330 new in package $75 2 12cm gated 35 housing $25 3 18cm gated 40 housing $25 1 16cm gated 40 housing has the volvo outlet. $25 1 14cm gated 35 housing 25 1 17cm gated 40 housing 25 1 hx52 center section no shafts...

Im having my tranny rebuilt and my planetary is alumniun. Is it worth the money for a steel planetary. truck is just a tow rig prolly never will be over 500hp but im having the tranny built to take it. Thanks

Ive been reading about the pot mod and cant seem to find how exactly it hooks up. Basicly my trans hangs in 2-3 shift when it shift to 3 im guessing the tq locks becuase it will pull hard. then it wont shift to od. With the od on the tq seems like its lock and unlocking. When i turn it off the...

Im working on my friends 92-93 i put a new lift pump, 3200gov spring, 14cm housing and a ground fuel pin on it. went for a drive today and ive got the full fuel screw bottomed out. It runs ok but on my 92 5sp i had the same mods and it ran so much better. It was tuned by a local guy before me. I...

Whats the size turbine wheel on the stock wh1c on a 92 automatic. Want to swap for a smaller housing and need to know the size.

Im wondering it my hx55 is going to be too heavy to use a welded flange on my manifold. I want to run a industrial manifold and using a bolt on flange puts the turbo 2 far down. I was gonna mill half the stock flange off. and then weld a 1/2" flange on tot he manifold. I just dont know if its...

I know that you dont want to run marine injectors on stock pistons, but is it bad to run it the other way around? I plan on rebuilding my motor with .020 over mahle marine big bowl pistons and didnt know if i needed to get a set of injectors while i was at it. Thanks.

I swapped a hx52 turbine wheel and 16cm housing onto my 55. Anyone know where to get a down pipe or flange for the hx52 it is a bit bigger than a 40 dp. Looked like a 4.5in outlet.

Ive got a bunch of 40 and 35 exhaust housings. Not sure on the wheel sizes but they would be good for machineing to fit other turbos, i used one for a 50. Ive got 6cm 12cm 35 housings and 14cm 16cm 17cm 40 housings $50 obo a piece. Will get some pics up soon.

will the hx52 turbine wheel and shaft fit in a hx55. ive got good 55 but the housing is goin to be too big, and ive got a 52 with a wrecked comp wheel and needs rebuilt. but the turbine shaft is good.

Is it possible to swap to a 6.7 Cam? Would this be benifical.

Ive got a new holset 451vgt turbo. The comp housing it been nicked up form bad packing Wheels are good and it spins free. This turbo has never been ran. Get a turbo contoler and have a big turbo that spools like a smaller one. Asking 1000 obo I can text pics. 317-504-8255

Ive got 3 HX35G turbos the comp housings are beat up from beening pitched around before i got them they all spin free and only have the normal shaft play. Ive got 2 HX40G Same with housings the ally spin free and have normal shaft play. $ 200 shipped for the 35s $ 300 Shipped for the 40s

Bought a motor that spun a bearing. Ive got all 6 injectors, HPCs, and fuel rail. Ive got the Stock Turbo. 400 for injectors figure theyd be good for cores so you can keep your stock injectors. Ive got all 6 cross over tubes and nuts 100obo Ive got the stock rail 200 obo. and stock he351vg...

I have a Hx55 i believe the its a 65 77 it came with a 22cm housing I found a 11cm housing and had it cut to fit my turbo. Am i going to run into any issues with this trubo. Not looking for a comp trubo just someing i can drive till i get a hx40 housing cut and welded

I have a 94 12v motor minus the pump and pump gear. Unsure of the condition of the motor havent done anything with it other that move it from one garage to the other. i was told it ran when pulled but im not for sure. It has come with block head and internals, exhaust manifold and wh1c turbo...

I have a VNT40 Trubo off a lly duramax, unsure of the mileage, its in good condition with no shaft play. asking 400obo I can text pics 317 504 8255 Chas

Ive got a stock trubo off a 7.3 unsure of the mileage but its in good shape no shaft play. asking 300 obo. I can text pics 317 504 8255 Chas

Ive got 2 garretts laying round the house. one is P/n 1831457c91 i believe it came off a 7.3 but i cant find anything else on it. the other is p/n 8973878962 its a VGT anyone have any idea of what they are size wise and what they come off of.

Ive got a 12v motor dont know the milage or the condition i was told it ran when it was pulled from the truck. The ppump was used in a 24v swap. for 1500 you will get the motor, with ve pump and lines, ppump lines, 160 ppump injectors, and hx50 (62-73?-19). Its missing one freeze plug and...