Search results

I have a '96 F-450 cab and chassis 2wd for sale. The cab and sheet metal is in good shape with no rust. The engine and transmission are gone. The rear diff is good but I can't remember what gear it had in it. I also have a '97 F-250 2wd 5spd with a 351w gas motor in it. The body is in really...

Used 7.3 long block with HPOP. No injectors. Engine was running when pulled but has low compression on one cylinder and excessive crack case pressure.

97 f-super duty rolling chassis only. Engine and transmission are gone. Sheet metal is in decent shape with a few minor dings but is rust free. Has a 12 or 14 steel flatbed with a wood floor. No title. Will sell whole or part out. $1,500 takes it with the bed.

I need a second truck and I don't drive it much anymore, that's the only reason I'm selling it. 2002 VW Jetta, auto trans,140,000 mile, leather heated seats, sun roof, two year old 25% window tin, new brake pads and rotors all the way around, tires are close to new 75% tread or better, power...

I am putting this stuff on here for a customer but the items are at my shop and I will be the one shipping them. All prices OBO. -Blue Chip Red Line box (came off of a '00 model truck) $900 -DDP competition 7x.015 (I believe, I will check the with a pin gauge) 24v injectors with roughly...

I have a OEM 4.10 Dana 60 ring and pinion (no carrier) and a Dana 80 ring and pinion with a limited slip carrier that needs a new home besides on the shelf in my shop. The 2 sets are from the same truck with aprox 120k miles on them. They are in very good condition and were only removed because...

There will be a 2.5 Diesel Truck class sponsored by HFS Diesel Preformance on Aug.3rd starting at 8pm in LaGrange, Ky. As of right now the class is set to be the last class of the night to allow pullers to get there from another pull going on that night. The pay out will be as followed 1st-$400...

There will be a 2.5 Diesel Truck class sponsored by HFS Diesel Preformance on Aug.3rd starting at 8pm in LaGrange, Ky. As of right now the class is set to be the last class of the night to allow pullers to get there from another pull going on that night. The pay out will be as followed 1st-$400...

I am listing this for a customer that is doing a P-pump swap, this is the only reason the pump came off the truck. The pump is in great running condition, feed by a FASS since it was new and never saw less than 15psi. Built 9-12 and has 3k miles on it. $1,250 obo shipped.

I'm looking for a good usable 6.7 crank.

I have 2 CP3's that I was saving in case a customer needed a good core but I'm getting tired of moving them from shelf to shelf so its time for them to go! Both these pump were on running truck when I got them they were taken off and replaced with bigger pumps. They have been sitting for a year...

I have a good used pump off a 6.5L chevy for sale that I dont need sitting around my shop. The pump was put on the truck back in Aug. of 2010 and only has roughly 3000 miles on it. The reason it is off the truck now is the motor spun a rod bearing and the truck is getting a new GM crate motor...

I have a '98 215HP 12v motor I need to get out of my shop, it has 150k miles on it. The motor came out of a wrecked truck and was running when it was pulled. The engine is now missing the timing cover, injection pump, vac pump, p/s pump,alt, and turbo. The pump and front cover was sold to a guy...

I have a 12mm 160hp p-7100 with full cut delivery valves, 5k gov springs (I also have a set of 4k that I can switch out if you would rather have them). Pump made 625CC's on the pump stand. The pump was only ran for 1 season and I am wanting to go to a 13mm for the up coming season this is the...

I have 4 265/75/16 BFG's that i need to get rid of they were on my pulling truck for 1 season ond have never seen the pavement other than driving through the parking lot to be loaded on the trailer. $750 Local pick up only. I am about 40min outside of Louisville,Ky.

I have a SCS mini-spool for a DANA 80 with 35 sline axles that needs to go. It is in good shape other than te cross pins have some scaring where I had a carrire split in half due to the bolts that hold the 2 halves to gether backing out but it is just cosmetic damage they are not bent. It was...

I have a set of DDP 5x15 competition injectors that need to go the were in my pulling truck last year. They run great and only a year old im am going to dual feeds sothat is why i need to sell them. These were $1400 new i'll take $900

I have a SCS mini-spool for a DANA 80 with 35 sline axles that needs to go. It is in good shape other than te cross pins have some scaring where I had a carrire split in half due to the bolts that hold the 2 halves to gether backing out but it is just cosmetic damage they are not bent. It was...

I have a Edge Juice with Attitude moniter laying around the shop that I need to get rid of. It is for an '04.5 thru '05 CRD and I'll pay the shipping! $475

I am looking for a RSV (Ag) governer for a p-7100 pump.Let me know what you all got! Thanks.