Search results

I'm at my wits end with this thing main shaft bearing went bad due to lack of oil and also melted the needle bearing in first gear. I replaced first gear all bearings synchronizers and main shaft put back together to book specs and it made it one mile down the road before doing the same thing...

Alternator slowly died on me today replaced it with a new one but only shows 12.4 v. Charging not 14. I'm reading lots on the ECM going bad and causing this, just wondering what your thoughts are on this??? It's always has a hit or mis when you turn the key on if the wait to start light and fass...

Looking for the shifter and tower if anyone knows were I can get one thanks!!

Anyone near east tenn with a good 24v block?? The old 53 finnaly let go and cracked, I will also be at Schied again if someone farther has one that's going thanks

Has any one on here tackeled rebuiling a g56 or know of a good shop??? Im wanting to swap out the 68rfe for the 56, Ive got one that I broke the shaft in out of my 06 but wanted to see if its cheaper to rebuild or just buy a new one, that is if I can find one

Got my fifth wheel up for sell it's 34ft two bedroom two bathrooms electric jacks, 2 electric slides and electric awning. Both slides have awnings also. Outside shower, gas/electric fridge, gas electric water heater. New tires new spare wheel and tire, satellite tv hook ups in all rooms, wood...

Selling my 08 quad cab long bed electric blue pearl 4x4 cummins. It's got 76,000 miles h&s mini max with trans tune, goose neck,airbags with in cab remote, five inch exhaust turbo back, s&b cold air, new head gasket with studs, leather, DVD in both head rests, road rhino bumpers, 35/12.5/17...

Guys im at a total loss truck has been fine till it got below 20 out now it blows cold air will not warm up even when pluged in. I can drive it about 25 miles and temp gauge and h&s gauge both show about 140 then it will jump to 245 and come back down to 190 then blow warm air but you have to...

Will a ECM out of a 99 auto work in my 98.5 auto??

Any one have a set of 8 on 6.5 three inch spacers for my dodge?? Got the 2 inch spacers but there still not enuf clearance between my tires.

98.5 got a miss in it once it warms up. When it's cold it idles smooth but once it's warming up it slowly gets a miss to it, it's never a consistent miss either. I've changed injectors unplugged sensors cracked injector lines one at a time with no change. It runs great under a load just does it...

Well boys and girls thought I would cut a fat hog in the azz by doing away with the factory metal tranny lines and cooler under the turbo and replace with a bigger cooler up front were the other cooler was. I did this because the metal lines had a couple kinks that i wasnt fond of and a bigger...

Guys bought the wife this car a month ago from an individual and within a months time it's burning a quart of oil every 130 miles. Called vw dealer they said possibly a turbo issue but I've got a little oil in coolant to mabe oil cooler cracked to??? Tore into it checked the turbo and the...

01 vp airdog150 twins 120hp injectors bla bla,anyways past couple weeks truck is getting worse at wanting to start, sometimes it fires right off and sometimes it dont, swaped out the comp for the juice and my fuel pressure idle or wfo stays around 15/18 psi. Runs great after it starts but cant...

Guys I need upper and lower both sides control arms for my 01. Cant find them anywere in the junk yard. And from what im told 01 and 02 are the only years that are the same dont know the differance but I need them now.Its got the skyjacker lift on it and i dont want it but bought it that way...

Just seen a pic in the may diesel power readers rides of a 01 srw with mega cab dualie fenders on the rear,kinda like the idea any one got any ideas if these bolt right on and fit the body lines or if you have to modify them??? He put the semi conversion wheels on it too,just wondering if any...

Hey Zach could i get a price on the 181/210 and your 110# springs for my 01 thanks all I hear and read is good stuff with your product!!!! Thanks Nate:clap:

HEY GUYS, new to this site from south central illinois got a 01 24v just swaped in my nv4500 got rid of that auto and put my hx40 over s475 on but need some f1 mach 7 injectors in a bad way to light it all up. I work for Norfolk Southern Railroad runing trains from st.louis to peru indiana...