Search results

swapped out my ho vp44 for an so with expectations of loss on bottom end and gains on top end, i noticed less power on bottom end less smoke and less power on top end and less boost. with a near stock setup will you notice a difference or do you really need a hotter setup to notice a difference...

brand new airdog 100 bought it for my 2001 dodge vp truck never installed it, sold the truck still in box, box has been opened but its brand new never installed includes everything it comes with, in northern california, petaluma. perfer local sell will consider shipping 4158471778 call or text $480

Saturday i put my a/d II 200 from my 12valve on my vp truck and pressure maxed my 40psi gauge instantly, i backed out the adjuster all the way and it went down to 32psi, then i removed one of the 2 springs completely and it dropped to 22psi. First off i thought for 94-98 they were preset at...

100hp ddp injectors, comes with new gaskets ready to install, they have been cleaned and redone by diesel performance center in phoenix, AZ bar has been set to 300, 0 miles since cleaned up and rebuilt, 15k miles on them since they were originally bought. $400 shipped.

1050 shipped had on truck for 3 months then totaled truck includes dp have reciept to prove age

i just put a new power steering pump on my truck and the power steering is worse than it was before and its full of ps fluid i turned the wheel side to side at least 30 times, dodge calls 20x and been driving it, and still barely works, any ideas other than napa gave me a junk pump? how long...

10k miles on these injectors bought new with reciept 1 year ago paid 1k for them, asking $700 ddp4 140 horse 12 valve fits 94-98had pop tested all pop at 270bar, almost new pm if intrested

have 10k miles all pop at 270 bar, asking $700 shipped

47re goerend triple disk 1800 stall tcs billet input output billet tcs servo suncoast rebuild kit suncoast gov sol. hts valvebody bd flexplate o/d is slipping selling complete trans parting truck out asking 4000$+ship or pick up im in phoenix

eclb 97 4x4 128k miles, Does anyone have any idea about what insurance does for aftermarket parts when totaling a truck? I do have all the reciepts that total up just over 12 grand in tranny, engine and fuel system. Very curious to what they will do,(other than bend me over) and how much i will...

So today i pulled my buddys ats tranny out of his truck (4wd) 47re and I replaced the pump/convertor seal, pump gasket, and the pump o ring. We didnt check the endplay before but after replacing the pump it has about 1/4 inch of endplay, the front drum did pop out of the rear drum slightly, but...

I'm looking to build a 13mm pump for a project truck, does anyone know the bosch part number for the desireable 13mm p&bs? i do have many 13mm kamatsu p&bs but not sure how the torque curve and timing adavance of the helix would compare to the bosch ones that most guys run in there trucks. The...

Does anyone know the bosch part number on an .022 delivery valve, I cant find it anywhere

So I havent driven my truck in a while and driving it tonight i noticed if i got on it hard in overdrive and lock up the rpms would rev up way quicker going up to 90mph, at full throttle rpms rev up to 2900 pretty fast it seems but still pulls pretty good. but if im only on it half throttle its...

so i went out to the track last night, and when i went to stage i could not build more than 3-4lbs of boost on the line rpms were right at 1500 no matter how long i power braked no matter on position of pedal i could not get it to move its got a 2000 stall converter from goerend that was rebuilt...

looking for a p7100 core pump as long as its for a 5.9 dont care if it works or not as long as its all there!

pulled off my turbo because i was only getting 40lbsof boost and it wasnt pulling hard or spooling very fast then saw it was cracked and wastegate is basically always slightly open and many small cracks travel the inside would this cause that big of a driveability effect and corelate to slow 1/4...

is there anything else other than turning barrels balancing rack plug pin timing the pump and afc what else is done to the ppump when getting it maxed on the bench?

looking for a quick rate cam for a 12mm ppump its a ca 180 pump

how do the barrels & plungers in an 8.3 pump compare to ours along with the cam would there be any advantages in any of the parts in one of these pumps?