Search results

I have a triple disk pulling clutch setup from Haisley. Installed at scheid 2012. has about 12-14 hooks. Works perfect. Its the big triple with the longer input shaft, spacer plate and all that jazz. I would also sell the dodge nv4500 trans that I ran with this if interested. Clutch set up was...

I have a set of 6 2012 6.7 cummins almost brand new injectors for sale. Came from a brand new cummins factory engine that a dealer installed. The truck had a previous turbo failure and the dealer installed a complete new engine without cleaning the CAC. Resulted in a runaway. There was massive...

Do the 12v rods directly replace a 6.7 rod? If not what needs to be done to run them. Going for stock compression.

Anyone get videos from the ppl pull in New Castle this past Sat night. Specificly the Ford...that broke at the end. Thanks.

Has anyone put a cr inplace of 6.7?

Got a 2012 with a windowed block. Looking for a short or long block either new condition or rebuildable. Located in IL but will travel to pick up. Text or call Matt. 3oniner two75424eight. Thanks.

Used dana 80 1480 u joint rear yoke. Also has Haisley billet straps. Bolts are little worn out but they're included. A little rusty from being left outside. $125 shipped. I can text a pic if you'd like. 3o9 2754248mg

I have a Ford Dana 80 rear out of an 04 F350. It is setup for pulling. It has a full spool from yukon. Ultimate 80 dif cover Branik 37/40 spline left/right axle Branik 40 spline drive flanges Branik 35 spline drive flange two spare yukon 1 piece axles. Broken ring and pinion currently...

I have a 2005 2wd dually truck that is pretty rough. Engine has 200,000+ miles and has some parts taken off the top. Still has injectors, have a good turbo, note said had fuel in the coolant. No lp oil pump, no front balancer, various other pieces missing. All electrical spoken for. Would...

It is time for me to grow my business and family, putting my engine/truck or both for sale. Truck: 99 Ford Ex cab, long bed Gutted cab and engine bay Driver seat w/ custom dash Hand throttle Air kill/fuel kill in cab Air kill/fuel kill at the rear of truck Dana 60 front 35 spline outer axles...

Looking for a pull in easter Mo, IL, or IN September 29 or 30. Looking for 2.6 or open class. Thanks!

Not too sure on the time, prob 6:00pm. Pullis is at the fairgrounds in Hoopeston, IL. IPA diesel 2.6 and open class.

I have a used kennys triple disk, has about 15 hooks, needs a new pressure plate inlay. Also have a good used 1 3/8 imput shaft, would like to sell together and would rather not ship. Located in bloomington, IL. Asking $1800 for all. Call or text 3o9, two 75, 42four 8.

http://www.marshallputnamfair.org/2012%20pdf%20files/Farm%20Stock%20Truck%20Classes,%20Entry%20Form%20&%20Waiver.pdf Any one planning on attending this?

Posting this for a buddy. Christian County Agricultural Fair | 4x4 STOCK TRUCK PULL Pretty good pull, good track, big beer tent, lots of food.

S480 Billet wheel, 96-88 turbine wheel, T-6 132 exhaust housing. Has maybe 15 hooks on it, was built by Haisley Machine to meet 2.6 bushing class rules, not protrusion. This turbo makes great power and is in excellent condition, only reason for selling is went to protrusion turbo. $1500 shipped.

Cam originally came from EEP. It is in good condition, ran this year for a few dyno passes and decided to try a different cam. Gear is welded on, intake center-line is at 98*. Engraved on the back journal is U-469 210*/222* @ .050 .323 Lift 106* $500 shipped call/txt 3o9 two754248

Need some help asap, on my pulling truck I have a brand new ford super duty master cylinder. I pulled the line out of the dodge master I was using last year and it fits just the same into the ford master with the small roll pin that hold the line in. So.....I've been trying to bleed this setup...

Couldn't make it this year, some one please post videos of pulls please.

Engine came out of a screw type air compressor. 3 cylinder, 33 HP, does 3500 rpm. Comes with starter, generator, flywheel, engine fan, and a complete wire harness with and instrument panel. Runs great. Perfect for mini tractor puller. $750 call or text 3o9 two75 four248