Search results

06 cummins how many more things can efi do compared to edge cts and smarty searched and seen some say they will never go with anything else than efi so I'm wanting to see what all can efi do compared to others. Sorry for my ignorance I have searched but I've been a 12v guy for the last 5years...

I changed my headgasket with a .020" thicker gasket can the decompression cause more smoke? I have never had done this before so kinda new to how the truck should reach to the change. Everything else stayed the same but the head, it was decked before I got it and I decked it .010" to clean it...

mustang dyno 250 http://www.youtube.com/watch?v=XKBXprjMBsc

just in case this has not been on here yet for the Pulltown, Bowling Green Ohio has added 4x4 diesels for there sat. night lineup should be a good show SESSION IV, 6:30pm Saturday Aug 20, 2011 Pro Stocks Unlimited Mods 2WD Trucks SS Open Super Stock Diesel 4WD Trucks Session IV only...

I bought new turbo base gasket (MLS T-4) for my ats manifold but the holes are off on the long spread about half a hole off, but the short spread is right on. Would any of you guy's know what size it is or kind of gasket I need to get. I know its not a T-6 or T-3 what is left. I did search...

has anyone ran this set up what was your like or dislike on it, the turbos are a h2e (64mm compressor) over a ht4d 86 or 88 mm compressor i believe. the pump is a maxed 913 supposed to flow somewhere in the 600 to 650 range. I did try a search and found some info on the h2e but nothing on the...

going to have a benefit pull sept 25 for the Bristly family from Manchester, it will be starting at 10am, address 4409 east race rd Leslie Mi 49251 turn in the first drive and follow back to track. This is the Leslie tractor club. We have not been having to many big tractors this year so I...

some of you guy's running one of those pot mods instead of tps do you set the volts to one setting and forget about it or do you adjust it when you are going to be drag racing or pulling. I am having problem with the throttle linkage or peddle position being low to get the volts high enough to...

how much boost pressure will a stock wastegate off a 97 take, I have a 66/74/16 turbo and was trying to make sure it is not opening up while trying to build boost. I adjusted the rod so the wastegate is almost all the way in so the spring pressure is holding the gate closed and I have the...

any reason why a ats arc flow air intake from an 03 wouldn't fit a 97 12v.

for you JD experts I have this turbo been laying around for a long time came off a 8630, something like 550cu. and around 250hp "we turned it up from factory hp" it was a 1978 "I think" if some one could tell me anything about it thanks. these are the # I got off the housing, AIR Research...

sorry for the ? but the direction's for 4 gsk kit say to leave the big spring in but make sure there are no shims so I pulled out the big spring and there was one shim on one side and two on the other, I did not put the shims back but I did put the big springs in is this right? And I noticed...

my dad's 29 died yesterday , no fuel anybody no any thing about this pump looks like a rotory pump syle but no sure were do you set the motor at to take it off top dead center on the motor then were on the pump. looking for any info thanks.

sold please remove from dodge products thanks. JR

ARP HEAD STUDS GLACIER DIESEL POWER -WALBRO FUEL PUMP 392 DDP 90HP NOZZLES AIR INTAKE EATON E-LOCKER IN THE FRONT AXLE BD SPEED ELIMINATOR BD VALVE BODY BD DEEP TRANS PAN PRO TORQUE CONVERTOR WITH LOW STALL “1600 RPMS” TORQUE PRO 2000 PROPANE FORM ATS WITH 10”X60” TANK TOP GUN FRONT LEVELING...

Montpelier OH, is any one going? and is it a good pull? 9-13-08 starts at 6pm stock diesel and mod class 8000#

I have an 99 dually 2 wheel drive that I can not get any boost out of it at all, can some one give me some ideas to look at or look for. Thanks JR

is anybody goin I think its this Friday starts at 7:oopm:rules:

any one going to the pull on Saturday 6/21 reg 4:30-7:00pm pull start at 7:00

looking for an E-Locker for my 03 cummins front AAM axle, were is the best place to get it? Are'nt they the same as the one for the d-max?