2.5 puller part out

5.9smoker02

5.9smoker02

New member
Joined
Aug 25, 2011
Messages
62
Beginning the process of parting out my 1996 Dodge 2.5 truck. Everything listed has no more than 15 hooks on it and has never saw the street.

Dana 80 Rear end: Yukon 35 spline spool, 5.13 gear, LPW cover, 1480 yoke, stock axles, no brakes-$1600

Nv4500 trans with bell housing, crossmember, and pedal assembly-$1200

241 dhd transfercase-$600

Kenny's Triple disk weighted clutch: upgraded hydros, billet input, starter spacer, release arm and throwout bearing all included-$2900

Rear Driveshaft for rclb with nv4500 and 241 dhd: includes 1480 joints and slip yoke-$450

Dana 60 35 spline spool: 2 hooks-$150

Pulling Products adjustable hitch-$175

(4) 315/75/r16 BFG All Terrains mounted on eagle alloy 058 16x10 wheels: 8 on 6.5 bolt pattern and includes lug nuts and two rear center caps. Zero street miles-$1500

FASS 220 lift pump for 12 valve: includes wiring harness, bracket, and all the fittings that came with it-$650

AFE intercooler: includes piping, boots, and clamps for 2nd gens-$1000

Dual electric fan setup with shroud: two 12" fans with brand new relay kit-$100

Autometer 6806 6k diesel tach: includes everything to install-$325

3 gauge pillar pod with autometer ultra lite 2000* pyro w/probe and 100 psi boost-$200

All prices obo call or text for more info or pictures: 937-564-5064 and my name is Justin. I will be listing some more stuff including engine parts here soon
 
Also interested in the fans if he doesnt take them pm shipping 54020

Sent from my DROID X2 using Tapatalk 2
 
New Madison, Ohio.
I have a couple individuals interested in the rolling chassis, so if things do not work out with them I will for sure start taking parts off.

Intercooler and fan setup are sold.

Anyone who was interested in the fan setup can still contact me as I can put together the same setup with larger fans, but it will cost a little bit more.
 
Dana 80 Rear end: Yukon 35 spline spool, 5.13 gear, LPW cover, 1480 yoke, stock axles, no brakes- Spool, gears and yoke sold. Open to offers on the housing

Nv4500 trans with bell housing, crossmember, and pedal assembly-$1200

241 dhd transfercase-$600

Kenny's Triple disk weighted clutch: upgraded hydros, billet input, starter spacer, release arm and throwout bearing all included-$2800

Rear Driveshaft for rclb with nv4500 and 241 dhd: includes 1480 joints and slip yoke-SOLD

Dana 60 35 spline spool: 2 hooks-SOLD

Pulling Products adjustable hitch-$175

(4) 315/75/r16 BFG All Terrains mounted on eagle alloy 058 16x10 wheels: 8 on 6.5 bolt pattern and includes lug nuts and two rear center caps. Zero street miles-$1500

FASS 220 lift pump for 12 valve: includes wiring harness, bracket, and all the fittings that came with it-$650

AFE intercooler: includes piping, boots, and clamps for 2nd gens-SOLD

Dual electric fan setup with shroud: two 12" fans with brand new relay kit-SOLD

Autometer 6806 6k diesel tach: includes everything to install-SOLD

3 gauge pillar pod with autometer ultra lite 2000* pyro w/probe and 100 psi boost-$200

Also have a Dana 60 Detroit locker: 35 spline, 4.56&up- $475
 
Do you have the 35 spline axle shafts for the Dana 60? To bad the locker isn't for a 3.54 gear.
 
Nv4500 trans with bell housing, crossmember, and pedal assembly-SOLD

241 dhd transfercase-$550

Kenny's Triple disk weighted clutch: upgraded hydros, billet input, starter spacer, release arm and throwout bearing all included-SOLD

Rear Driveshaft for rclb with nv4500 and 241 dhd: includes 1480 joints and slip yoke-SOLD

Dana 60 35 spline spool: 2 hooks-SOLD

Pulling Products adjustable hitch-$175

(4) 315/75/r16 BFG All Terrains mounted on eagle alloy 058 16x10 wheels: 8 on 6.5 bolt pattern and includes lug nuts and two rear center caps. Zero street miles-$1400

FASS 220 lift pump for 12 valve: includes wiring harness, bracket, and all the fittings that came with it-$600

AFE intercooler: includes piping, boots, and clamps for 2nd gens-SOLD

Dual electric fan setup with shroud: two 12" fans with brand new relay kit-SOLD

Autometer 6806 6k diesel tach: includes everything to install-SOLD

Also have a Dana 60 Detroit locker: 35 spline, 4.56&up- $450

12mm ARP2000 head studs for a 12v. Two torques on them- $350
 
No sorry I do not have it anymore.

I also have the short block out of the truck for sale now.
it consists of:
-12v Mahle marine pistons, flycut .100 deep and coated, .020 over bore.
-Stock rods with arp rod bolts.
-Balanced bottom end with 14mm arp main studs. Crank is drilled for roll pins for the damper.
-Hamilton 207/220 cast cam, block has cam bearings in all the journals. Bronze thrust plate.
-24v tappets and a set of stock length billet push rods.
-It will come with the front gear case, cam gear and retainer, oil pan, oil pump and cooler, and an aluminum tappet cover. Everything only has 15 hooks on it. Ran brad penn oil which was changed every 5 hooks. Looking to get $3500 obo for it
 
Wish I had some cash I would take you up on that motor. Did you ever have it in the rollers? What was your fueling setup?
 
Levi_plummer said:
Wish I had some cash I would take you up on that motor. Did you ever have it in the rollers? What was your fueling setup?
Click to expand...

Yeah it was on a chassis dyno but we couldn't get any numbers unfortunately. Never tried again after that. As far as fuel goes it had a Columbus built 12mm on it, with single feed 5x.020s and 0.093 lines. Injectors were a little big for the set up though.
 
You must log in or register to reply here.
Back
Top