2002 HO 5.9 engine, VP engine parts, NV5600 4wd & other NV5600 stuff.

Mark Nixon

No Savior among the flesh
Joined
Feb 26, 2009
Messages
8,678
2002 HO 5.9, complete from flywheel forward, accessories, combo-pump (PS-Vac) turbo, ECM, missing the alternator, which I may have a replacement, engine reportedly ran great and the injection pump has definitely been replaced, $1700/obo.

2000 24 valve longblock, no VP, lines, ECM combo pump, will part out, has an un-cracked '53' block, good for crank (tone ring style), rods, oil pan, fan hub assembly, head, rocker arms (has pressed-on lash caps), A/C mounting bracket, compressor (spins nice), buy it as it sits, $850 or I'll part out.

2002 6 speed ECM with main engine harness, was from a runner, $300 w/harness, $250 w/o SHIPPED.

2001 6 speed ECM, # P3947412, also from a runner, MIGHT have a harness for this one, as well, $300 w/harness, $250 w/o SHIPPED.

2003 NV5600 4WD, minor pilot bearing damage on the input, otherwise it could probably use a ball-detent assembly, because it shifted hard if you rushed it. Didn't grind, comes with choice of early shifter or late shifter, $1750.

2003 NV5600 2WD, lower miles rebuilt, under 15k miles, $1850.

2000 NV5600 2WD, ran out okay before I pulled it, small input, so it's cheap, $1200/obo.

2002 NV5600 4WD CORE I found it in a core pile, was told it has bad synchros, has a pound or 2 of sand in it now, partially spins over, as-is for a core, $500.

SEVERAL (4 or so?) partially dis-assembled NV5600s. Only 1 good 2WD mainshaft, a couple of 4WD extensions and bellhousings, plus other knick-knack internals, make an offer, otherwise I will sell pieces of them.

I also have an inordinate amount of 5.9 Commonrail engine parts that needs new homes, so please ASK!

Reply, PM or call 402-780-5127 for needs!

I AM MAKING A TRIP TO THE COLUMBUS, OHIO NEXT WEEK AND I CAN DELIVER ANY OF THIS ON THE TRIP. DON'T BE AFRAID TO ASK!!!
 
Sure would, on your dime, of course.
Which one are you interested in?

Mark.
 
Hey Mark, just checking on what the block number is on the 02 motor? Since it is a HO motor the ecm should be for 6 spd?
 
Last edited:
I thought I'd put that in there.
180,000 miles.

I didn't mention it in the ad, but I also have a shortblock HO engine that's a 55 block.

Mark.
 
I saw a rod and lever in the back of the junker I drive, while cleaning it out to go pick up a POS CR engine yesterday.
I'll look for it to-morrow and see if it's compatible or not.

Mark.
 
It'll need bored.
It got water down a couple bores and I don't think it'll hone.
Has the pan and timing case still on it.

$300?

Mark.
 
I do have a drop in shortblock.
Actually, it has a cylinder head on it, too. :)

Coincidentally, it's a '53'. LOL
It was a 5 speed engine in a 2000 truck with @ 200k on it, no leakage.

Damn, I REALLY need to off some scrap!


Mark.
 
I need a vp gear nut and washer, and tps bolts. Apparently my local dodge dealer doesn't know how to order stuff for a truck as ancient as mine.
 
Did you need a GEAR?
I have the nut and the TPS bolts, but no washer.

Mark.
 
No I have the gear, at some point of it sitting the nut got lost. How much for the bolts and nut?
 
Back
Top