96 Dodge Rolling Chassis and pulling parts.

1996 Dodge Ram Ex cab long bed Chassis that was setup for the 2.6 class. I can either sell as just a roller or with all the parts listed below. Motivated seller so the quicker the better i am no longer interested in finishing it. Body is pretty rough but it has alot of high dollar parts installed. Interior is gutted besides steering column. Clean title. Mirrors, headlights, grill etc. come with. Exterior pieces were taken off when the body work was started but that obviously was never finished.

With the chassis will be included as listed below.
custom adjustable hitch
Traction Bars
Driveshaft loops
5.38 gears with lockers front and rear
Standalone hydraulic steering
Auto meter Tach w/memory
Posi lock cable lock for front axle engagement
6-33x12.5x16 trxus STS tires 85%
Eagle alloy rims on the front
Front and rear driveshafts 1410 front/ 1480 single piece rear
Hood Stack
241 Transfer case
$3000 obo

Parts that can be included for the right money are as follows
24 valve engine been inspected/ magna fluxed & cleaned w/12 valve rods w/Arp bolts, needs one piston. The other 5 are good and cut for the cam listed below $750
ATS 3 piece t3 manifold $250
2.8 BorgWarner Charger, new turbine shaft & wheel, and new billet intake wheel. Never ran since the new cartridge $1100
5x.018 injectors $500
24 valve head ready to go, new valves, new seats, new guides, 5 angle valve job. Lots of money invested in this head. $1500
Scheid Pulling Cam 234/254 $450
Airdog 150 $400
Side Draft intake $500
14mm 12 valve head studs $300
Billet push tubes $300
12 valve 120# valve springs $175
ppump-12 valve .093 injection lines $300
engine girdle & main studs $400
NV4500 with top cover, rear housing, bell housing, and true BILLET input $1000
Frozen Boost air to water intercooler $200
SFI approved Bellhousing Scatter Blanket $300

I'm sure there's stuff i am forgetting so i'll add to the list as i remember. This motor setup is sitting at the machine shop ready to be put together. I would sell all the parts and the truck in a package deal for $8000 obo or the listed prices above if i seperate stuff. For $8000 your essentially only paying for the parts and getting the chassis free. show contact info call or text anytime.
 
Last edited:
I will get pictures as soon as i make it to the machine shop. Not sure on the cut depth i will also get that info when i get there.
 
Auto meter Tach w/memory
6-33x12.5x16 trxus STS tires 85%
Eagle alloy rims
Hood Stack
241 Transfer case
2.8 BorgWarner Charger
Airdog 150
14mm 12 valve head studs
12 valve 120# valve springs
ppump-12 valve .093 injection lines
engine girdle & main studs
NV4500 with top cover, rear housing, bell housing, and true BILLET input
SFI approved Bellhousing Scatter Blanket
ALL SOLD

5x018 Injectors were sent to weston to be gone thru and had new nozzles put on. $650
 
With the chassis will be included as listed below.
custom adjustable hitch
Traction Bars
Driveshaft loops
5.38 gears with lockers front and rear
Standalone hydraulic steering
Posi lock cable lock for front axle engagement
Front and rear driveshafts 1410 front/ 1480 single piece rear

24 valve engine been inspected/ magna fluxed & cleaned w/12 valve rods w/Arp bolts, needs one piston. The other 5 are good and cut for the cam listed below $750
ATS 3 piece t3 manifold $250
5x.018 injectors (just gone thru w/new nozzles $650
24 valve head ready to go, chopped intake shelf, new valves, new seats, new guides, 5 angle valve job. Lots of money invested in this head. $1500
Scheid Pulling Cam 234/254 $450
Side Draft intake $500
Billet push tubes $300
Frozen Boost air to water intercooler $200

$4000 takes it all.
__________________
 
WEBERBUILT said:
With the chassis will be included as listed below.
custom adjustable hitch
Traction Bars
Driveshaft loops
5.38 gears with lockers front and rear
Standalone hydraulic steering
Posi lock cable lock for front axle engagement
Front and rear driveshafts 1410 front/ 1480 single piece rear

24 valve engine been inspected/ magna fluxed & cleaned w/12 valve rods w/Arp bolts, needs one piston. The other 5 are good and cut for the cam listed below $750
ATS 3 piece t3 manifold $250
5x.018 injectors (just gone thru w/new nozzles $650
24 valve head ready to go, chopped intake shelf, new valves, new seats, new guides, 5 angle valve job. Lots of money invested in this head. $1500
Scheid Pulling Cam 234/254 $450
Side Draft intake $500
Billet push tubes $300
Frozen Boost air to water intercooler $200

$4000 takes it all.
__________________
Click to expand...
Do you have any pictures of the chassis? If you could, send them to
716-359-0962 thanks
 
You must log in or register to reply here.
Top