98.5 Dodge 2.6 puller

Johndeeretech

Johndeeretech

New member
Joined
Jan 10, 2009
Messages
219
1998.5 Dodge 2500 149,000 miles on whole truck

ENGINE:
Industrial Injection Super Phat Shaft 66
Industrial Injection Dragon Fire VP44
B D Diesel 3 piece exaust Manifold
Redline Diesel 6X.20 injectors
Frozen Boost Water to air intercooler (run ice water)
Stainless Steel .93 lines had the crossover tubes machined out to .98
Fass 150 lift pump
Glaicer bigline kit
Electric cooling fan
Head re torqued holds 50-65 psi of boost every pull no problem
Custom turbo inlet with 6" volicty stack
Blue Chip FMS box
Dr. performance stage 3 timing box

Last time it was on the dyno in May it made 628 Hp. 1,195ftlbs.
Have all the dyno papers

TRANNY:
Sun Coast triple disc converter
All billet shafts thru out in tranny
mag tech double deep tranny pan
HTS valve body
Red clay clutches
the housings for the clutches have been machined to hold more friction discs and steels
T/C lock up switch
tranny temp gauge
Have all the invoices for both builds of the tranny

Axles:
3:55 gears
dana 60 front lincon locked
dana 70U rear lincon locked with 35 spline axles(insted of the 32s) and percsion gear ring and pinion

Exterior:
Rino lined bed
Rino lined to the first body line on truck
blacked out lights all over
10 inch stack

Other:
Track bars and saftey chains
Tranny blanket
drive shaft loops
u joint shields
sled bumper bars
removable weight bracket
adjustable pulling hitch
fully adjustable suspention stops ( 2 1/2in. all thread that can be screwed up and down to suit)
fuel and air shut offs with saftey cable ran to the back to hook on sled

there is probley alot of things im forgeting

$15,000 o.b.o but would like to trade for a older 12 valve puller (need a new project) 1-815-674-7826

t2.jpg

t3.jpg

t4.jpg
 
Well Pat, stepin up with the big boys huh? JK are you gonna come back around here and pull with us? We are starting a class with the Illiana pullers assoc. In fact we have a meeting dec 4 at noon in champaign at hooters.
 
ILLINOISRAM said:
Well Pat, stepin up with the big boys huh? JK are you gonna come back around here and pull with us? We are starting a class with the Illiana pullers assoc. In fact we have a meeting dec 4 at noon in champaign at hooters.
Click to expand...

ya I moved down to TN in june I wish I could come up every weekend and pull with you guys but that would be a hell of a drive to make every time but if you know of any truck for sale or trade up by you guys just give me a shout Im usually up there every month or so just lookin to step up to 2.8 and I need a winter project to spend some more money on that I dont have:doh:
 
well the snow is falling and still not gone 13,500 bump new #s from beans dyno and sled pull 12/4/10 633 hp 1,300ftlbs
 
Last edited:
can this be a dd? i have a 1996 dodge 3500 with a phat shaft71 and alot of engine work and tranny work. too much to list unless your intersted
 
smokn3500 said:
can this be a dd? i have a 1996 dodge 3500 with a phat shaft71 and alot of engine work and tranny work. too much to list unless your intersted
Click to expand...

this could be a daily driver if you just put a heat excanger on it insted of the ice water we run through it as far as driving it on the street it might be a little bit smokey and its road manners probley wouldnt be the best with both front and rear axles lincon locked but it can be done just P.M. me with info on your truck
 
You must log in or register to reply here.
Back
Top