Common Rail stuff, engine parts, ECMs, wiring, etc.

Mark Nixon

Mark Nixon

No Savior among the flesh
Joined
Feb 26, 2009
Messages
8,678
2007 5.9 shortblock from an AUTOMATIC burn job, had some water down it, may need bored .020, has flywheel forward, with a decent oil pan, NO front accessories, includes the head that is cracked on the intake, $750.

2007 5.9 LONG block, lost a rod, block appears salvageable if you weld up a 3/8" hole, crank is toasted, still has head, newer injectors, newer CP3 pump, WIRING harness, some front accessories, oil pan is dented up (off replacement engine from a wreck), was going to combine with the one above for a great builder, sell as is, NO ECM or TURBO, for $1000.

3 CP3 cores, 2 crispy ones that turn (no FCAs), 1 decent one with an FCA, as is, $175 SHIPPED.

HE341 Turbo cores, no turbine damage, good enough to rebuild, $175 each SHIPPED.

HE351cw Turbo cores, no turbine damage, good enough to rebuild, cannot guarantee a pressure sensor, otherwise complete, $175 each SHIPPED.

2007 fuel transfer tubes, w/ retaining nuts, set of 6, $75 SHIPPED

2006 Engine harness, has both plugs on the ECM, only 1 ground loop cut off, otherwise decent, $150 SHIPPED.

2006 Engine BAY harness, for fusebox, headlights, what the engine harness plugs into, only missing the plugs for the left and right ABS sensors and the vacuum pump plug, $100 SHIPPED.

Short section of 2006 dash harness that includes ignition switch and APPS plug, $35 SHIPPED.

2005 Engine harness from an AUTOMATIC truck, includes BOTH ECM plugs and all engine plugs, $160 SHIPPED.

2004.5 AUTOMATIC transmission harness, no cuts or damage, $75, SHIPPED.

2005 FUSE BOX, from a lower miles 6 speed truck, includes cover, NO HARNESS, $100.

2003 FUSE BOX from a 6 speed truck, includes cover, NO HARNESS, $100.

2005 APPS, $35, SHIPPED.

2003 MANUAL APPS assembly, with cable and short harness cut, $100.

2005 MANUAL ECM, part # 3975241, was on a running, driving truck a week ago, $250.

2004.5 AUTOMATIC ECM, part # 3971104, also a runner from a recently parted wreck, $250.

Please reply, PM or call 402-780-5127.
 
Last edited:
Mark Nixon said:
2003 MANUAL APPS assembly, with cable and short harness cut, $100.
Click to expand...

More details on this please. Would like a couple of pics as well. Im looking to swap one of these on my 03 auto to relocate its current position OFF the head. LMK. Thanks. :Cheer:
 
It is located under the driver's side battery tray and has a cable that runs over to the firewall like your current one does.

It has 6 wires inline, rather than the square plug with 6 wires that yours currently has, so splicing will be necessary.

I'll see what I can do for pics.

Mark.
 
I've never messed with em before, but im no stranger to wrenchin on these trucks; I know what they are, more (or less) what they do, and where they are located. IS it a fairly straight forward plug-n-play swap? anything else I'll need (i.e. nuts, bolts, cable, and/or mounts/brackets) would greatly be appreciated. Ideally, i'd prefer anything that touches it come with it; minus the batt tray. Hopefully i'll finally be able to cleanly install my CAT filter!
 
Last edited:
I've no clue on the swap between the head-mounted to the tray-mounted, I just ran across it in a yard and figured it would be a better choice for remote mounting.

It has 6 wires in a row.
IIRC, the head-mounted version also has 6 wires, but the plug is more square-shaped.

The best thing I could think to do would be to get pinout info on both APPS' and see if the color codes are for the same layout and functions.

Mark.
 
I was just looking and it's POSSIBLE that the wiring conversion link off of a Timbo APPS is the solution, instead of splicing.
I seem to recall having one of the wiring links around.

101_0458.JPG



Mark.
 
You wouldn't have a transmission harness for a 06 48re, would you?

Sent from my SAMSUNG-SGH-I717 using Tapatalk 2
 
I don't have one, but I can keep my eyes out for one.
Is yours for a 4WD?
If so, is it manual shift (NV271) or electric shift (NV273)?

Mark.
 
What are you looking for and what year, Taylor?
Still looking for VP cams?

Mark.
 
Mark Nixon said:
I was just looking and it's POSSIBLE that the wiring conversion link off of a Timbo APPS is the solution, instead of splicing.
I seem to recall having one of the wiring links around.

101_0458.JPG



Mark.
Click to expand...

Ok, sounds good. Shoot me your best shipped price for the stuff. and paypal info too. Thanks.

*Im also looking for a set of useable 'low mileage' 5.9 CR injectors*
 
Last edited:
bigtexss said:
Ok, sounds good. Shoot me your best shipped price for the stuff. and paypal info too. Thanks.

*Im also looking for a set of useable 'low mileage' 5.9 CR injectors*
Click to expand...

FYI, I did indeed find the wiring off the Timbo APPS pictured above and the link will NOT work with this particular APPS, as the inline plug is slightly larger.
However, you could use the square end and splice it to the APPS I have, though you should still have the pinouts for both to make sure you don't fry something.

Mark.
 
I don't have one I can personally vouch for.
One of the "cores" I mentioned above was reportedly a "good lower miles unit", but I am unwilling to say it's good, myself.

Mark.
 
2006 Engine harness...SOLD!
2004.5 AUTOMATIC ECM, part # 3971104...SOLD!

Mark.
 
CURRENT LIST:

2007 5.9 shortblock from an AUTOMATIC burn job, had some water down it, may need bored .020, has flywheel forward, with a decent oil pan, NO front accessories, includes the head that is cracked on the intake, $750.

2007 5.9 LONG block, lost a rod, block appears salvageable if you weld up a 3/8" hole, crank is toasted, still has head, newer injectors, newer CP3 pump, WIRING harness, some front accessories, oil pan is dented up (off replacement engine from a wreck), was going to combine with the one above for a great builder, sell as is, NO ECM or TURBO, for $1000.

3 CP3 cores, 2 crispy ones that turn (no FCAs), 1 decent one with an FCA, as is, $175 SHIPPED.

HE341 Turbo cores, no turbine damage, good enough to rebuild, $175 each SHIPPED.

HE351cw Turbo cores, no turbine damage, good enough to rebuild, cannot guarantee a pressure sensor, otherwise complete, $175 each SHIPPED.

2007 fuel transfer tubes, w/ retaining nuts, set of 6, $75 SHIPPED

2006 Engine BAY harness, for fusebox, headlights, what the engine harness plugs into, only missing the plugs for the left and right ABS sensors and the vacuum pump plug, $100 SHIPPED.

2005 Engine harness from an AUTOMATIC truck, includes BOTH ECM plugs and all engine plugs, $160 SHIPPED.

2004.5 AUTOMATIC transmission harness, no cuts or damage, $75, SHIPPED.

2005 FUSE BOX, from a lower miles 6 speed truck, includes cover, NO HARNESS, $100.

2003 FUSE BOX from a 6 speed truck, includes cover, NO HARNESS, $100.

2005 APPS, $35, SHIPPED.

2003 MANUAL APPS assembly, with cable and short harness cut, $100.

2005 MANUAL ECM, part # 3975241, was on a running, driving truck a week ago, $250.

2004.5 AUTOMATIC ECM, part # 3971104, also a runner from a recently parted wreck, $250.

Please reply, PM or call 402-780-5127.
 
You must log in or register to reply here.
Back
Top