CR parts

[bigstacks95]

Parting out an 06 CR motor. Has bottom end noise. Deal pending on the head. Otherwise:

6 good injectors stock nozzles 120k miles $800 obo shipped
Freshly rebuilt HE351CW $500
Fuel rail and lines no sensor: $200
06 intake horn $40
Starter $100
Trans adaptor had 48re $100
Flexplate 48re $100
motor mounts $50
Pushrods $50
bare Block $500
Cam $40
CP3 works well no FCA $200
valve cover $50

Have a few other things but none of the accessories (alt, ac, etc)

 

[bigstacks95]

Spun a rod bearing on #6, crank probably needs turned. Also broke rings on 3 and 4, so block might need to be bored.

 

[Thegrampatrk]

I will give 300 pay pal fpr the turbo amd elbow

 

[bigstacks95]

NEW LIST! make offers guys!!!

Injectors- $800 SHIPPED
Oil pan- 75 bucks
pickup tube- 25 bucks
rocker arms plastic retainers- 50 bucks
pushrods- 25 bucks
crank pickup tone ring- 50 bucks
valve cover riser- 25 bucks
fuel rail and lines- 200
misc fuel lines between pump and rail or filter- $10 each
filter housing- $25
connector tubes and retaining nuts- $25
motor mounts from 2006- $50
Stock cast exhaust elbow- $40
Transmission wiring harness- $50
Ground cables- $20 each have both
valve cover $50
Camshaft $40
Cylinder head- $500 with valves and springs and intake plate
valve cover gasket/wiring harness for 2006- $40
HE351CW turbo with sensor FRESH REBUILD- $500
exhaust manifold tapped for pyrometer incl. bolts and heat shield- $100
Starter- $100
Grid heater- $50
Intake horn- $40
CP3, No FCA- $200
CP3 gear- $25
Turbo oil supply line- $40
Turbo oil drain line- $40
Flexplate 48re- $100
Trans oil cooler- $50
Bellhousing adaptor- $100
Pistons and rods are NOT for sale
Crankshaft- $100 NEEDS TO BE TURNED!!!!! #6 rod bearing spun
2006 bare block- $500 MAY NEED TO BE BORED!!! #3 and #4 had broken rings
Gear housing- $100
front cover- $50
MISC bolts, ask what you need I probably have it. $You pay the shipping and my time$

 

[bigstacks95]

Bump! CP3, head, turbo, injectors, oil pan and valve cover riser are all gone. Mane an offer on anything!

 

[turboram]

Do you have a harness?

 

[buzzindozen]

I know you said you don't have the accesories but i was wondering if you have the upper most idler pulley, the one above the fan hub assembly?

 

[bigstacks95]

I wish I had a harness, it would be on my 05 if I did....

No idler pulley, sorry.

 

[bigstacks95]

Bump! Updated list! Make offers!

pickup tube- 25 bucks
rocker arms plastic retainers- 50 bucks
pushrods- 25 bucks
crank pickup tone ring- 50 bucks
fuel rail and lines- 200
misc fuel lines between pump and rail or filter- $10 each
filter housing- $25
connector tubes and retaining nuts- $25
motor mounts from 2006- $50
Transmission wiring harness- $50
Ground cables- $20 each have both
valve cover $50
Camshaft $40
valve cover gasket/wiring harness for 2006- $40
exhaust manifold tapped for pyrometer incl. bolts and heat shield- $100
Starter- $100
Grid heater- $50
Intake horn- $40
Turbo oil supply line- $40
Turbo oil drain line- $40
Flexplate 48re- $100
Trans oil cooler- $50
Bellhousing adaptor- $100
Pistons and rods are NOT for sale
Crankshaft- $100 NEEDS TO BE TURNED!!!!! #6 rod bearing spun
2006 bare block- $500 MAY NEED TO BE BORED!!! #3 and #4 had broken rings
Gear housing- $100
front cover- $50
MISC bolts, ask what you need I probably have it. $You pay the shipping and my time$

 

[BLT4SIN]

exhaust manifold by chance?

 

[bigstacks95]

Yup I have an exhaust manifold its tapped for a pyro I've been asking 100 plus shipping

 

[cummin95]

Do you have a tranny harness to fit a 04.5?

 

[bigstacks95]

Got one from an 06 do you think its the same? I can get pics for you to compare if you want.