Dodge 3500 2wd RCLB, P-Pumped 24v kit, Built Transmission

Cursedtofirst45

Cursedtofirst45

New member
Joined
Oct 29, 2008
Messages
680
Recently bought a 1999 Dodge Ram 3500 for $1700. Tranny was toast when i bought it, so i sent it out to get built up by my buddy @ Palo Verde Customs in Buckeye, Az. Upon fixing the transmission, we discovered that the truck's lift pump was toast and wasnt providing any pressure to the IP. We replaced the lift pump, and found that the IP was toast as well. At this point, with this much money involved in building this truck as is, we decided to p-pump it. Today, went to go see it, started her up, and it was knocking like a son of a *****. Couldnt hear it before the ppump swap because the truck had a cracked exhaust manifold and minimal fuel pressure. Decided to cut my losses today.

Complete P-Pump kit to convert 24v to a p7100 injection pump
-includes either 180 or 215hp pump (not sure which one is on there)
-Front cover
-Injector Lines (.093)
-Fuel Shutoff Solenoid
-Mounting brackets

Like i said, this is a complete kit. You won't need to address anything else besides beefing up your stock lift pump to run this 12v injection pump on your 24v. Will let this complete kit go for $2500


Built PVC Transmission (47re 2wd)
-Billet Single Disk converter
-Alto Clutches
-Increased clutch packs
-Race Valve Body
-Heavy Duty Overload Spring, Band, Backing Plate
-New Pump
-Capable of holding 500 hp, flexplate being the only true weak link now.

$2500, and will deliver for cost of fuel.

Also have complete rolling chasis for 1999 Dodge Ram 3500 Reg Cab Longbed 2wd with good interior and paint(red). Will also sell complete rolling chasis. Dana 80 has 3.54 gears. Taking offers.

-Eric
 
Last edited:
073.jpg

074.jpg

075.jpg

076.jpg

077.jpg
 
Kick Start said:
How much you lookin to get out of the rolling chassi?
Click to expand...

$1000 for just the chasis with clean title (no bed, no front clip)
$1500 for chasis with front clip

Will deliver for cost of fuel.

Its not a ppump kit from scheid, columbus, haisley or any other reputable shop. It was built by my buddy at Palo Verde Diesel in Buckeye, Arizona. I know the lines are .093, i think from Scheid. But other than that, all of the brackets and relocation of the tps were custom fabricated.
 
Dana 80 3.54 - $700 plus shipping

Anything else, just ask for the price

Intercooler, radiator, condensor, complete ac system, full interior, 3 stock radios, Everything from engine and lots more still available.

Built Transmission- $2000
 
lbdodge24v said:
What is left? Wouldn't want to sell the whole truck? Just wondering here.
Click to expand...

Everything minus the bed on the truck is left. Cab, interior, axel, full front end, etc. I'd like to sell the whole truck for 1500 with a clean title minus the engine and tranny. Have a guy coming to look tonight inquiring about the whole truck.
 
Alright, where are you located, or did I over look that somewhere. Also if he doesn't want it, I may be interested. Are the engine and tranny still there too, may be interested in some of that too, if the truck is still available. I need a project lol.
 
lbdodge24v said:
Alright, where are you located, or did I over look that somewhere. Also if he doesn't want it, I may be interested. Are the engine and tranny still there too, may be interested in some of that too, if the truck is still available. I need a project lol.
Click to expand...

Transmission is still available, engine as well.

Located in Gilbert, Arizona. I can deliver for the price of fuel depending on how much of this stuff you take off my hands.
 
Wish i was in a better position to by hole rolling chassie. I need a clean 2nd gen chassie. This 1st gen body style just aint cutting it
 
You must log in or register to reply here.
Back
Top