garage clean out sale - turbo parts, hitch, suspension, etc

GOT-Torque

GOT-Torque

is
Joined
Jul 2, 2007
Messages
5,284
5" guillotine (blast gate style) $30
poly 24V 98-02 engine mounts new in bag $40
slip yoke (ujoint cap hole measures 1.185, OD on slip yoke is 2.2", and it works with a 31 spline shaft) $75 guessing a 1410 yoke for a NV5600?
adjustable hitch for 2" receiver $100
lightweight rear suspension for 98-02 dodge pulling truck (includes the lightened leaf springs, lightweight spacer block, u bolts, base plate, and bump stops (picture shows half of the parts) $200

turbo parts
S475 wheel and cover new 171691 on wheel $200
S480 wheel and cover used 171984 on wheel $200
S470 wheel new 168299 on wheel $25
S465 compressor wheels new 168407 on wheel $25 ea
T6 0.9 housing for small center section charger (works with a 83/74 exh wheel) $150
87.4x80.4 turbine wheel new 171783 $250
83.5x74.3 turbine wheel new $150
79.8x73.4 turbine wheel new $150
169011 center section new (complete with bearings) $150
169011 center section new $150
169012 center section used (missing the two small bearings that the shaft spins on, otherwise complete) $100
2 of the 171328 cast compressor wheel $50
171242 cast compressor wheel $50
T4 0.9 housing for 83/74 wheel $150
T6 1.1 housing for 83/74 wheel $50
T6 1.58 housing (I'll have to find the part number) $50

If anything seems out of line shoot me an offer.

1108141350_zpsj19dsdsq.jpg

1109141703_zpskyc8ry3n.jpg

1109141702a_zps68nvyair.jpg

1109141702_zpsh32rhznz.jpg

1108141309_zpsgaekjd9y.jpg

1108141259_zpsmgintbrh.jpg

1108141243b_zps52jlytle.jpg

1108141243a_zpsx2fyny6x.jpg

1108141243_zpshstzebqn.jpg
 
I'll take the T6 1.10 housing and used empty center section please.
 
Last edited:
I'll take the 75 wheel and cover.

83 turbine wheel and cartridge.
 
The following is all spoken for (pending a few payments)

5" guillotine (blast gate style) $30
S475 wheel and cover new 171691 on wheel $200
S480 wheel and cover used 171984 on wheel $200
83.5x74.3 turbine wheel new $150
169012 center section used (missing the two small bearings that the shaft spins on, otherwise complete) $100
T6 1.1 housing for 83/74 wheel $50
 
do you have any clamps for the 96mm turbine? From the center section to the turbine housing? or a good 96mm center section
 
If Carl backs out on the 1.1 I'll take it next!!

Also the guiotiene if he backs out.

Sent from my iPhone using Tapatalk
 
Last edited:
why are the 1.1 housings so popular? I must have thrown ten of those things in the iron pile in the past... I may be able to find another one if I look in the garage hard enough.

Here's a deal for someone, I have a blem adjustable gear for $200 (need a core gear in return). The gear didn't get put on the mill correctly so two of the slots just get into the casting holes on the gear. I ran it on my pulling truck for a short time so I know it won't cause any problems. This gear has been laying around about 4 years and is one of my original designs so the smaller alignment holes don't line up with the alignment holes on the hub (later design). In any case, it would still allow quick timing adjustments, just loosen the 6 outer bolts and then rotate the balancer the needed degrees of adjustment using a timing tape and pointer.

1109142006_zpsyuyv6fim.jpg
 
If you can find another 1.1 T-6 I would take it. Even if it's a little rusty.


Sent from my iPhone using Tapatalk
 
What's left:

poly 24V 98-02 engine mounts new in bag $40
slip yoke (ujoint cap hole measures 1.185, OD on slip yoke is 2.2", and it works with a 31 spline shaft) $75 guessing a 1410 yoke for a NV5600?
adjustable hitch for 2" receiver $100
lightweight rear suspension for 98-02 dodge pulling truck (includes the lightened leaf springs, lightweight spacer block, u bolts, base plate, and bump stops (picture shows half of the parts) $200

turbo parts
S480 wheel and cover used 171984 on wheel $200
S470 wheel new 168299 on wheel $25
S465 compressor wheels new 168407 on wheel $25 ea
T6 0.9 housing for small center section charger (works with a 83/74 exh wheel) $150
87.4x80.4 turbine wheel new 171783 $250
79.8x73.4 turbine wheel new $150
169011 center section new $150
2 of the 171328 cast compressor wheel $50
171242 cast compressor wheel $50
T4 0.9 housing for 83/74 wheel $150
T6 1.1 housing for 83/74 wheel $50 (have one left)
T6 1.58 housing (I'll have to find the part number) $50
blem adjustable gear is still available too.

If anything seems out of line shoot me an offer.
 
got my parts already. Just as described and right quick delivery. Thanks Jesse!
 
You must log in or register to reply here.
Back
Top