Ppumped 24v built engine - complete - also S400 turbo

GOT-Torque

GOT-Torque

is
Joined
Jul 2, 2007
Messages
5,284
ppumped 24v with lots of work. Selling it complete without the injection pump and turbo. Has billet front cover, tappet cover, all freeze plugs, adj pump gear, dual valve springs, ti retainers, major port/polish on the head, oring'd, 12mm arp head studs and 12mm mainstuds, aftermarket cam, arp rocker studs, 6 new bigger bowl pistons with ceramic coating on the tops, block stiffener, 0.093 SS lines, fluidampr. I rebuilt it last year and I opened up the clearances slightly so it was appropriate for a higher rpm pulling engine. Everything was balanced in the bottom end as well. Currently painted cummins red. PDI T4 manifold with ports drilled in all runners. I have datalogs of how it runs and video's from this year too.

Selling it complete, no plans to part it out. Priced for a quick sell. $8000

Turbo is available seperately. S400 based and comes with two polished race covers (3.0 inlet and 2.8 inlet). Big turbine wheel. Have a T6 and a T4 housing available for it. $1650 for everything

Please send all requests for info or pics to my email jesse (at) EATSOOT (dot) com - I can't seem to keep my PM's cleared out. Thanks

Located in Falls City, NE

Here's my last run with it.

[MEDIA]http://www.youtube.com/watch?v=ifnAh6c_Pgc[/MEDIA]
 
Reason for selling? Are you quiting pulling or going bigger?
 
SMOKIN-U said:
how did you place at platte?
Click to expand...

ended up 11th

2.8 Class
1. Troy Wakeman Lonejack, MO 337.08 01 Chevrolet
2. Cole Stephens Gaston, IN 332.10 Dodge
3. Adam Hallien Fort Wayne, IN 326.02 97 Dodge
4. Chris Muhs Birmingham, IA 315.08 98 Dodge
5. Jon Swartzentruber Loogootree, IN 312.10 Chevrolet
6. Evan Smoot Eaton, IN 312.05 97 Dodge
7. Chris Webb Van Wert, OH 304.08 Dodge
8. Jerry Crow Marion, IA 302.06 05 Chevrolet
9. Dan Barnes Hume, MO 300.01 Dodge
10. Terry Biggs Noblesville, MO 297.08 01 Dodge
11. Jesse Neddenriep Falls City, NE 293.11 01 Dodge
12. Rob Hall Smithville, MO 289.03 02 Chevrolet
13. Chris Barton St. Joseph, MO 283.05 03 Chevrolet
14. Adam Scholting Gretna, NE 281.05 02 Dodge
15. Nathan Palmer Bolkow, MO 274.10 03 Gmc
16. Tony Haile California, MO 272.01 96 Dodge
17. Ryan Bauer Louisburg, MO 266.07 Dodge
18. Theron Jarecke Culbertson, NE 264.02 96 Dodge
19. Adam Harmon Polo, MO 262.00 95 Dodge
20. Scott Barcus Hopkins, MO 248.04 06 Dodge
21. Darren Binkley Dunlap, IA 207.08 03 Dodge
22. Whitney Curtis Divide, CO 108.11 97 Dodge
23. Brian Moody Aubern, NE 47.11 Dodge
24. Brad Hodler Russellville, MO Broke
 
Bump for a good guy. Stickin with the 24v or goin a different route with this new build?
 
little different this time... will be a whole new animal.

Other than the pump and turbo on this current engine, it could be street driven (daily driver/sledpuller). I did it for a few thousand miles after the build.
 
pulled again tonight but broke one of my rear axles at the line. Not much of a video to watch...
 
Axles are from Branik Motorsports and Stan is taking care of it for me. I think it may have broke at the end of my pull the week before and I didn't realize it until this hook.
 
You must log in or register to reply here.
Back
Top