Recent content by russcone

Have a lml that had an oil leak that I could only trace as a upper oil pan leak. I pulled everything apart to clean and reseal, while that far into it I went ahead and pulled the rear adapter plate. I replaced the seals and resealed that also. I never took apart the oil cooler, although I did...

04.5-07 5.9 industrial injection 180hp injectors. Ran fine when removed in 2017, was removed to go bigger. Have been boxed up and sealed since removed. Need gone. $950 shipped or trade for s467. Sent from my moto z3 using Tapatalk

Trucks a 06 with ats dual fueler, 100% over exergy's, single 467. Couple of months ago every blue moon the truck would have a fluctuation in RP. Would clear up and run great. Ended up having my injectors sent out due to a bad stator o ring, came back and the issue was still there. The last few...

Precision billet one peice input shaft with a slight twist. Picked this up last year to with the intention to use and never did. $225 shipped. Also a set of full cut delivery valves that I picked up the same time as the input shaft. $200 shipped OBO. Sent from my XT1254 using Tapatalk

180hp injectors, late 04.5-07 5.9l. Were originally industrial injection full body 100hp and I put the 180hp nozzles on in October. I have made one pass on them with no lockup at 7600lbs and ran a 7.6 at 93 mph. I have noticed are they are very hazy and have some rattle around 50-60k miles. Only...

Okay trucks a 06 auto with dual pumps, exergy 100% overs and the current turbo setup is a htt 66/73/13 and 75/96/1.32. I'm not really sure what this setup is capable of producing power wise. I'd like enough air for close to 1000 but for now I'm trying to stay around 850ish. I was thinking I...

Just finished building my compound setup and finally put a few hundred miles on it. The setup is my old htt 66/73/13 I ran as a single with a box s475. Truck spools better just driving around and towing then it did as a single. I'm seeing 55psi total boost and 30 from the primary. The truck...

Posting for a good friend. 2006 dodge 2500 ccsb should be a sound 650hp. Truck has 164,864 on the clock. Motor only has right at 5,000 miles due to a cracked ring. Had full body 100s, e.d 63/68, studs, tuning by starlite, all new sensors, and a bag of parts installed with the build. Trans has...

mid July i sold my 03 and bought a 06 with only 7000 miles on the current performance setup (bone stock before). all the work was done in April at a shop in north Georgia. the parts are 10mm h&s stroker, industrial injection long life 100s, htt66, fass, studded, intercooler/intake, and built...

okay i sold my 03 a couple of weeks ago and finally had the chance to wire up my system. my old truck i built a non divided, ported console box from the floor up the back seat. this new 06 i ended up building a box under the seat for the same subs. i raised the seats 3/4" and fiber glassed a...

Lately I've been having some issues with p2509 and p0088 and the truck just cutting off ect... I dielectric greased every connection except those under the fuse bock and at the trans. Replaced both cam and crank sensors, replaced a bad fan clutch and fixed two wore wires. I think I solved that...

Built my new radiator brackets today, the old ones set the radiator about a 1¾" to low with my electric fan. It caused it to be way to close to the HB. Also put some heat wrap on my hot pipe and started the downpipe. Because of me not knowing if I won't to run the stack or exhaust out the...

Piping is now done. I'll pick up the stuff this week to do the exhaust. Still debating on single stack or coming out in front of the rear passenger tire. Sent from my XT1080 using Tapatalk

Made some progress tonight. Got the hot pipe tacked together. I'll do the cold pipe and also the turbo support brackets in the morning. Sent from my XT1080 using Tapatalk

As the title says I have a dana 80 for sale or trade for 12v. Performance parts. Came from 94 dually 3:55 ratio drum brakes. $800 obo. Located sw Georgia. Stuff would trade for manual vb, valve springs, 5x18 injectors, 4-5gsk's, billet input etc. ------------------- 2003 CR 100hp BMS...