Recent content by turninheadz94

Wanting to sell or trade my 63/68/14 bw 3rd gen style turbo with 15 minutes run time on it. Getting away from twins and wanting to try a big single s472,s475 and cash depending. Thanks 92B5FA23-1BAC-40FD-8E62-B293B0B28E0C.jpg Photo by lilsmokey94 | Photobucket

Like the title says I'm looking for a ht4b new or used but has to be in great shape thanks for looking. Cross874x4@gmail.com or call text 8oneseven2339315

I did a search within this chapter and found a similar problem to mine, I can turn my regulator all the way in on my ad 165 2 that has under 2k miles and has brand new filters and the pressure won't go past 38psi at idle, something about the plunger setup when i first got it on and installed had...

Well just finished my build and swapped my 181 delivery valves out for 7mm 100cc delivery valves. It cranks fine and all cylinders are firing it is just really rough. Has anyone else ever had this problem? I want something that idles smooth yet still flow well.

My htt62/65 snapped in half and the exhaust wheel came down and messed my ht3b up. Would like to find a ht4b to replace it! Please pm me if you have a new or rebuilt or have a source I have found nothing! Thank you

Like the title says, the connectors from my 94 cab harness are way different then the 97 engine harness and pcm harness. I have no problem swapping to deustch connectors because i use that and gm connectors at work all the time. Justbwondering if its still gonna function

I have a smarty s06 revo pod. Can install TNTR if desired. One of the pins that screws into the smarty is bent, idk how it happened but everything looks as it did brand new. Going the efi route so I no longer need this, it is unlocked ready to go, have box and all paperwork to go with it. 500...

I need piston rings, main bearings, lower and upper gasket set, rod bearings, and a oil pump for my 94 12 valve. Also a p7100 nut that holds the gear tight. Im rebuilding the engine and not sure if I should use new rod bolts or not. Thank you

I'm rebuilding my motor and wondering if I need heavier than 60lb springs for the 181-210 cam I'm going to run, don't plan on going past 3900rpms. I had around 75 psi boost before.

About how much is a good price to have a valve job done and oringing my head? Just lookin for a heads up to see if the local shops around here are high or not

My crankshaft started haveing enough runout to make a difference where whith throttle would move my clutch engagement so im tearing it down as we speak. Just wondering how much of a daily driver/track guinea pig im gonna have. I swapped my nv4500 in a even trade for a 47re ats extreme or...

Im trading my 5 speed for a ats billet 47re. My question is whats the best way to remove the wiring from the other guys truck so that i can use the pcm and still have the trans shft. Is there a easy way to pull the trans wiring without swapping the whole engine harness

Ht2b 62-65-13 over ht60 twin kit htb2 needs rebuilt I bought this set up about 3 months ago and noticed alot of play in the 62/65/13 but when oiled it wasnt too bad guy was supposed to send rebuild kit but never did now cant find him. Inducer wheel shows some damage now and needs rebuilt. Ht60...

Im looking for 2 sets of these valve cover breather setups to run on my truck eerything needed to replace 2 and 3 valve cover and 4 and 5. Thanks

I have messed and messed with my gov springs just to see if i could get anymore fuell and with that came rougher and rougher idle. So i had my pump benched and maxed and when it got back i looked how i had the gov springs.. One side i had it as tight as i could get at .097 and other side was at...