Search results

I’ve got a 98 12v truck and I’m converting over to 24v. It’s a new build and I was going to put the water temp sensor on the side of the head between the map sensor and the ait sensor. The sensor on the 12v head is down between 4 & 5. Has anyone else done this before. Would it get an accurate...

I’m looking for this setup. Scheid made these years ago. I’d prefer to have it in working condition Or needing rebuilt. No junk housings. Or if you just have the exhaust housing in good condition from this setup that would work also. Sent from my iPad using Tapatalk

Brand new. Ported - Gasket matched. Comes with bolts. No gaskets. $375 buyer pays shipping Sent from my iPad using Tapatalk

I need to repace my injectors in my 06. I keep getting po2146 and po2149 codes. And with 188k on them i think its time to replace. Looking at a small set like 50hp. So are reman good enough or should i go with new ones?

No speed sensor? Tach doesn't work, fuel pump runs and shuts off very quickly. Engine stumbled for a sec and then ran fine. How and or what do i need to fix.

I need a ECLB frame with no rust! Only need frame, nothing else. Would like one from a quad cab. So everything bolts up. Not sure if the older frames will work

I know this has been done before. I am interested in knowing what the CFM gains are. Like before and after. And if its worth the cost of everything. If you have any info and dont want to post please PM me.

7.3 powerstroke engine .030 overbore Mahle pistons, Flycut with Totalseal rings. Brand new Hypermax rods with ARP bolts. Block is notched for 3208 vavles. New Rods & Mains. New Oil pickup tube, Oil pan is set up for duel drain backs. Cam is a Billet Roller from EEP. No specs were given to us...

I have a Sinister Fuel sump that is a month old, and the gasket is junk. When i installed the sump, i removed the tank from the truck. I had to fix my float. When i put the sump in, the gasket was very soft. It squeezed out from around the sump. I did'nt overtighten the bolts, and i used...

Im looking for a project truck. 98 12v or 98-02 24v. Wanting a truck with a bad motor. I would like one with a good body, that doesn't need body work. I don't want a dually. Single wheel only. Would like a manual but. I might consider an auto. Must have clean title. Must be a complete truck...

When i went to order the spacers the other day, The guy told me i had to cut the studs off. So i didn't order them. Is this true, or a big concern. Truck is a 98 Dodge. Going to run 285s, stock steel inner o58 outer.

Is it possable to not use the filter in the trans, and replace it with an aux filter. A spin on type. And just have one filter. I was thinking of using a trans cooler with a fan and using a spin on type filter in line with it.

What to stack with an Edge Comp Drag. I'm looking for a programmer or tuner. I know all 3 will give about 60hp. I've heard the smarty is good. The Edge EvoHT and Superchips are cheaper. I'm looking for any info before i buy.

This block has been to the machine shop, and ready to be assembled. Block: Bored 20 over, Finish honed at 4.041 Resurfaced .010 Line bore was checked, it was in spec. Price= $750 Also have 3 12v crankshafts that are used. Price= $175 Buyer pays shipping or pick up.

The heated seat switch for my 2000 just flashes now and then goes off. The other side works fine. Is the switch bad or do i need to look at something else.

I was looking at valve springs the other day, and saw several different one's. Most are single. But i saw one that was double. Any advantage to a double over a single spring. All were rated at #110.

I have a 2.6 Batmo with less than 10 hooks on it. Batmo race cover. 87/80 wheel. Two T4 exhaust housings with it 1.0 and a 1.25. Both with HX40 flange. Built buy Bullseye. Absolutely nothing wrong with it, just don't need it anymore. Price $1800. PM me for faster reply.

I need the top steel line for the hydro boost. This is on a 98 Dodge.

I know as a general rule of thumb a 3.0 (or bigger) is what you want. But why not a 2.6. I'm sure it would spool super fast. And be good for towing. Please enlighten me.

Looking for a CR head. Would like to have it complete, with valves. Must be or have been checked at machine shop for cracks. I will want to see the paper work on that.