Search results

Anyone have recommendations for a good place to buy a good stock injection pump for a 2001 auto?

I thought I've seen somewhere a picture of how a guy fixed his breather problem but I can't find the picture. It looked like he ran the line from the from the stock location at the top of the timing case to the oil fill cap to vent it back in the valve cover. Anyone seen anything like that? Have...

Anyone know where I can find the tranny line that comes out of the front drivers side of the tranny, crosses under the bellhousing and goes to the heat exchanger on the passenger side under the turbo?

I'm not sure who to talk to and your office is closed now but here is the situation. Last week we installed a dual disc clutch in a 2010 dodge. Everything went fine and we test drove it, it shifted smoothly with no problems. The customer picked it up and they drove it around with no problems, I...

Anyone have the cummins part number for a 2010 6.7 rear main seal? Cummins guy is trying to tell me it is $5.00 and part number 5259499 but I am pretty sure that is not right.

2007.5 Dodge 3500 Mega Cab Laramie 4x4 for sale. 6.7l Cummins, 87,000 miles, 1500 miles on complete engine rebuild. Suncoast automatic 6speed tranny. Leather seats, sunroof, door sill plates, painted ventshades and mirrors, body color rhino liner, front and rear dvd, Kenwood stereo. Crower...

My pickup has been in rebuild stage for 1.5 years and now its done and ready to drive. I started it very briefly and let it run for 5 seconds or so and shut it down. I just wanted to see if it would start. The next day I brought my smarty out to change from 14me to 28me. I was going to take 14...

My brother just got his block back from the machine shop and #1 and #5 pistons are installed backwards, as in the writing facing to the back of the block. These pistons are reused stock pistons from his cracked 53 block and they don't have a FRONT stamped on them like other pistons I have seen...

My brother is in the process of replacing his cracked 53 block. We tore it down and brought it in to the machine shop and the builder said he thought the pistons might be a little loose. He said the piston to wall clearance on the new block is 5 thousandths. Does anyone know the cummins min-max...

Is there going to be any problem running King main bearings on a street driven Cummins? Reason I ask is I had them installed and my builder commented on the fact that they dont have oiling holes. I asked if that would be a problem and he said probably not, the bearing manufacturers know what...

Any word about the 68rfe tuning?

Turbo for sale, ball bearing, water and oil cooled, 10,000 miles, 68/77/1.06 t4 exhaust. $1200 plus shipping.

Anyone have stock 6.7 nozzles laying around they want to get rid of?

My brothers 53 block is cracked and he hasn't decided what to do about it. I'm just kinda seeing if anyone has a non 53 block and what they are going for. Also how much is shipping on a block? Located in Washington state.

Brand new PDI exhaust manifold, 2nd gen, t4 outlet, 3 piece. $500 shipped. I'll get pics up a little later.

I was wondering if I could put this here? http://www.google.com/cse/home?cx=007590534210329038489:bb4an846zj4&hl=en

I'm wondering what to get my ring gaps set at. I brought the engine in to a shop that has a good name for high performance engines. Problem is that he is a gas engine builder. So my question is are high hp gas and high hp diesel similar as far as heat in the cylinder? Ring/piston swelling rates...

I need a 24v vacuum pump, anyone have one?

I'm in the process of swapping a 518 from a 92 and have some questions a I havn't found answers to. I swapped the throttle valve from the 518 to the 47rh but I'm wondering if the linkage deal that mounts to the frame and has the 3/8 rod that goes to the bracket with the rubber grommet that is...

Brand new in the box 6.7 Flux 4s. I'm going to bigger nozzles so I would like to sell these. $1000 plus shipping. Location Goldendale, Washington. [/IMG]