Search results

Hi, looking for an Ag style exhaust manifold for a 12v. 90 degree flange with a center dump. Shipping would be to NY 13369. If anyone has any leads before I buy new, it would be greatly appreciated. Thanks

I have a used triple disc clutch that I bought from another member on here a few months ago. Fits NV 4500/5600 Has 5 passes since being refreshed. Comes with fork and alignment tool. Going a different route with the truck, no longer needed. Asking $1200 or trade towards a towing dual disc

I have 2 core 160 and a 180 pump. AFC housings are intact, no linkages. Asking $450 shipped each for the 160 pumps. $525 shipped for the 180 pump.

Looking for a good used 12v Cummins 3 piece T3 exhaust manifold and 425 or equivalent studs. Items will need to be shipped to northern NY. Let me know what you have. Thanks

I bought a used Autometer electric fuel pressure gauge, there was no sensor included. Do they just use a generic 5v 100 psi sender? I found a $25 one on ebay, or a $150 Autometer one on Amazon. Is there a big difference between the 2, other than one being from China? They are both 5v, 100 psi...

I'm wondering if the MFWD models of the 2-85/105/110 had a front axle disconnect, or were they all time four wheel drive? We had a two wheel drive 105 a few years ago, but I haven't been around any 4x4 Whites. If they had a disconnect, where in the cab was the lever? Assuming it was...

Set of used ARP 425 head studs from a 2012 6.7. Two torques on them. Once at installation, second at 1000 kms. All nuts and washers included. Looking to trade for 12v head studs or selling for $450 + shipping. Pm for contact info. Thanks

I have a slip yoke for 241 dld transfer case. $60 shipped Pm for contact info.

A local guy had a pull at his farm on the weekend, but it got rained out. Not one to give up, he was able to convince the mayor and the municipal foreman to run the pull on the road. Has anyone seen that before? What's the best/worst brush pull you have seen?

Stock input shaft out of an NP 271 transfer case that was mated to an auto trans. Not sure if anyone needs one? I swapped in a 29 spline shaft. Not too sure of value. $80? Let me know if I'm off on price. Thanks

Hi, I'm looking for the rear case for a 241 dhd. Truck is a '96. Let me know what you have. Thanks

1998.5-2000 Edge comp box. Came off of a 2000 24v that I bought. Ran fine, as far I know it isn't unlocked (hot or drag). Wires to the MAP sensor plug were cut, but can be rewired. $275 shipped.

I am looking for just the tail housing for a dhd. Let me know what you have. Thanks

I have a used set of base model mirrors from my '02. Manual adjustment, glass is in good shape. Has the odd spot on it. $80 shipped Thanks

I have 2 complete sets of rockers, bridges, etc. Came from high mileage engines. $100 shipped Thanks

I have a Vacuum/power steering pump from a '96 12v. 150k miles on them. $140 shipped. Thanks

I have a '98 53 block engine for parts. Mileage is unknown, but I'm assuming it's high (300k). Block is scrap, VP pump, manifold and turbo are sold. Rest of engine is complete. I've only pulled a few things, let me know what you need. 47 RE adapter plate and mounting bolts- $100 Stock flexplate...

Hi, just wondering if anyone has MCed or announced a pull before? A buddy of mine is sponsoring a local pull, it's pretty small time, nothing too serious, and he was wondering if I would do the announcing. I don't know if I'm the best choice, but if he's in a bind I'll help him out. It's...

I have a 210 hp complete engine. Came out of a Ford F700. 847 injection pump (untouched)- $400 Front timing case and cover- $150 Lines and injectors- $200 Remote reservoir steering pump- $100 Dual fuel filter housing with sediment bowl- $50 Lots of other stuff (alternator, AC compressor...

Hi, I'm looking at a turbo with the 1.10 compressor housing, EBV delete and a 1.0 exhaust. Is it much better than my stock turbo with just the ATS Comp housing? Truck is a dd and tow truck in summer. Thanks for any info.